EBS EBS-150 Drome - Contents:p Age; Getting Started; Introduction

I
NTRODUCTION
• G
ETTING
S
TARTED
S
PECIFICATIONS
7KH(%6'URPHLVDQXOWUDFRPSDFWDQGXQEHOLHYDEO\OLJKW:EDVV
FRPERZLWKLQFUHGLEOHVRXQGILOOHGZLWKXQLTXHSRVVLELOLWLHV7KHROG9LNLQJ
P\WKVVD\V7RNHHSWKHGLDEROLFDO)HQULVZROIIURPNLOOLQJWKH1RUVH*RGV2GLQ
7KRU)UH\DDQGWKHRWKHUVDQLPSRVVLEO\VWURQJQHFNODFH'URPHZDV
FUHDWHGZKLFKZRXOGNHHSWKHHYLOZROIXQGHUFRQWURO
2
BALANCED OUTPUT: Output Level nominal - 10 dBv
Output Impedance < 10 ohms current lim.
Frequency Response +0/-3 dB 35 - 20k Hz
Dynamic Range: linear 102 dB typ.
A-weighted 105 dB min.
XLR Connections 1-GND, 2-Hot, 3-Cold
Options Pre/Post EQ,
GND LIFT
EFFECTS LOOP: Loop Signal Level nominal -10 dBv
Gain Unity (1:1)
Output Impedance (Send) <100 ohms
Input Impedance (Returns) 47 kohms // 100 pF
Loop Mode Serial or Parallel
Phantom Power optional 2 x 10V 20 mA
LINE OUT: Output Impedance: < 5 kohms
Nominal Signal Level: 0 dBv
TUNER OUT: Output Impedance: < 1 kohms
Signal Level: Instrument Level
POWERAMP/ Continuous Output Power 150 W RMS
CABINET: Cabinet: Impedance 4 ohms
Crossover Freq. 4.5 kHz
Resonance 90 Hz
Volume 28 l
AUXILIARY INFO: Power Requirements max 200 W
Mains Protection: T2A Fuse ( 230V )
T4A Fuse ( 120/100V )
Dimensions: 17" (432 mm) Width
11" (285 mm) Depth
19.8” (502 mm) Height
Weight: 36 lbs. ( 16 kg )
Shipping 40 lbs. ( 18 kg )
References: 0 dBv = 0.775 V RMS
Specifications are subject to change without notice!
19
(%6 'URPH lU GHQ PHVW NRPSOHWWD
NUDIWIXOODRFKIOH[LEOD NRPSDNWD EDVFRPER
VRPQnJRQVLQKDUWLOOYHUNDWV0HGLQE\JJG
VWHUHRPRQLWRUIXQWLRQ VXSHUDNWLYD ILOWHU
RFK GHW NODVVLVND (%6 OMXGHW HUEMXGHU (%6
'URPH HQ PlQJG  P|MOLJKHWHU VR P
EHVNULYVLGHQQDPDQXDO0HQI|UVWDYDOOW
I|OMHU HQ LQWURGXNWLRQ VRP KMlOSHU GLJ DWW
EOLEHNDQW(%6'URPH
A
TT KOMMA IGÅNG
...
1. Packa försiktigt upp combon.
2. Se till att alla kontroller är ställda fullt
motsols. Fortsätt med att ställa de tre
filterrattarna märkta BASS, MIDDLE
och TREBLE till mittposition. Leta upp
filteromkopplaren och ställ den i läge
BYPASS. Se även till att omkopplaren
märkt Character är i uttryckt läge. Nu
är ljudet i
EBS Drome
"nollställt" och
redo för att skapa just ditt personliga
sound.
3. Koppla in din bas.
4. Spela hårt på basen och vrid upp GAIN
ratten tills PEAK dioden börjar blinka.
Än har du inget hörbart ljud, men en
perfekt signal att jobba vidare med.
5. Sök och vrid upp VOLUME ratten till
lämplig ljudnivå.
7KH (%6 'URPH LV WKH PRVW SRZHUIXO
YHUVDWLOH DQG FRPSOHWH FRPSDFW EDVV
FRPER HYHU EXLOW :LWK EXLOW VWHUHR
PRQLWRUVHFWLRQDQG D VXSHU  SRZHUIXO(4
WKHXQLWRIIHUVDQH[WUHPHO\ZLGHUDQJHRI
SRVVLELOLWLHVZKLOHPDLQWDLQLQJ WKDWFODVVLF
(%6 VRXQG 7KHVH EULHI WXWRULDOV ZLOO KHOS
\RX WR EHFRPH DFTXDLQWHG ZLWK VRPH RI
WKHIHDWXUHVRIWKH(%6'URPH
G
ETTING STARTED
...
1. Carefully unpack the bass combo.
2. Check that the controls are set fully
counter clockwise. Proceed by turning
the three filter knobs marked BASS,
MIDDLE and TREBLE to mid position.
Locate the filter switch and set it to
BYPASS. Make also sure that the
switch marked Character is in its’ outer
position. Now the
EBS Drome’s
settings are "zeroed" and ready to be
personalized.
3. Plug in your bass.
4. While plucking the strings as hard as
you would during your hardest playing,
gradually increase the GAIN knob until
the PEAK led starts to flash at peaks.
5. Move over to the VOLUME knob and
adjust for the desired output volume.