To Next PageTo Next Page
Need help?Do you have a question about the Echo PPT-260 - PARTS CATALOG SERIAL NUMBER 04001001-04999999 and is the answer not in the manual?
Orange engine cover for the power pruner.
Standard 5x16 screw used for assembly.
Top guard for the engine assembly.
A small collar component.
Cover for the muffler assembly.
Standard 5x12 screw used for assembly.
Component used for standing the unit.
Standard 5x22 screw for assembly.
Standard 5x20 screw for assembly.
The main fuel tank for the power pruner.
A component used as a spacer.
A standard 5mm washer.
Standard 5x16 screw for assembly.
Assembly for venting the fuel tank.
A clip for securing components.
Vent pipe for the fuel system.
Return pipe for the fuel system.
Fuel supply pipe for the power pruner.
Fuel grommet for sealing.
Filter for the fuel system.
Assembly for the fuel cap.
Gasket for the fuel cap.
Connector for the fuel cap.
A circlip for securing components.
Fixture for the main pipe.
Standard 5x28 screw for assembly.
Standard 5x18 screw for assembly.
A clip for securing components.
Assembly for the fan cover.
A circlip for securing components.
The main fan case component.
Pin used for alignment.
Ball bearing for the clutch mechanism.
A circlip for securing components.
Drum component of the clutch assembly.
Clutch shoe component.
Shaft for the clutch assembly.
A standard washer.
Spring for the clutch assembly.
Assembly for the starter pawl.
An E-ring for securing components.
Spring for returning the starter mechanism.
The pawl component of the starter.
Standard 8mm nut.
Complete starter assembly.
A standard screw for assembly.
Drum for the starter assembly.
Starter rope for manual starting.
Guide for the starter rope.
Handle grip for the starter rope.
Spring for rewinding the starter rope.
A standard nut.
Standard 4x12 bolt.
Knob for securing the air cleaner cover.
Lid for the air cleaner assembly.
Air filter for the engine intake.
A plate to prevent something.
Standard 5x60 screw.
Housing for the air cleaner.
Gasket for the intake system.
An insulating component.
Standard 5x25 screw.
Gasket for the intake system.
The engine's carburetor.
The WYJ-250B model carburetor.
Screw for the cable bracket.
Bracket for cable mounting.
Throttle valve assembly.
Screw for idle speed adjustment.
A swivel fitting.
A standard washer.
A clip for securing components.
The main body of the carburetor.
An O-ring seal.
Carburetor jet for fuel flow.
Assembly for the pump body.
Inlet screen for the carburetor.
Screw for the metering lever pin.
Needle valve for fuel inlet.
Spring for the metering lever.
Pin for the metering lever.
Metering lever for the carburetor.
Body for the air purge system.
Purge bulb for priming.
Cover for the primer pump.
Screw for the pump cover.
Carburetor repair kit.
Packing ring seal.
Pump gasket seal.
Pump diaphragm.
Inlet screen for the carburetor.
Needle valve for fuel inlet.
Metering lever for the carburetor.
Gasket for the metering diaphragm.
Metering diaphragm.
Kit for gasket and diaphragm.
Packing ring seal.
Pump gasket seal.
Pump diaphragm.
Gasket for the metering diaphragm.
Metering diaphragm.
Heat shield for the exhaust system.
The exhaust muffler component.
Standard 5x55 screw.
A standard washer.
Screen for the muffler.
Gasket for the exhaust system.
Guide for the exhaust component.
Standard 4x10 screw.
The ignition coil component.
Standard 5x16 screw.
A grommet for sealing or fitting.
Cap for the spark plug.
Terminal for the spark plug cap.
Spark plug model BPM-7Y.
Spark plug model BPMR-7A.
Ignition lead wire.
Engine flywheel.
Flange nut for 8mm application.
Ground lead wire.
Standard 5x10 screw.
The main short block engine assembly.
The engine cylinder.
Standard 5x22 screw.
Gasket for the cylinder.
Kit containing piston and related parts.
Piston ring.
Piston pin.
Circlip for the piston pin.
Spacer for the piston pin.
Needle bearing component.
Assembly for the crankshaft.
Kit for the crankcase.
Oil seal for engine components.
Ball bearing 6001.
A circlip for securing components.
Gasket for the crankcase.
Standard 5x25 screw.
Oil seal for engine components.
Heat shield for the exhaust system.
Gasket for the intake system.
Gasket for the intake system.
Standard 5x25 screw.
Upper part of the gear case.
Guard for the sprocket.
Flange nut for 6mm application.
Brand label for the product.
Retaining ring component.
Washer for the clutch mechanism.
The drive sprocket.
Threaded stud for 6mm application.
Lower part of the gear case.
A forming pad component.
Pipe for oil outlet.
Automatic oiling system assembly.
A circlip for securing components.
A spring component.
Plunger component.
Cap for the oil pump.
A spring component.
A standard washer.
Adjustment needle component.
Standard 5x10 screw.
Impulse pipe for the engine.
Fuel grommet for sealing.
Strainer for the oil system.
Shaft connector component.
A circlip for securing components.
Ball bearing component.
Bevel gear component.
Worm gear component.
Shaft for gear assembly.
A gear component.
A collar component.
Assembly for venting components.
Assembly for the oil cap.
The oil tank for the power pruner.
A collar component.
Standard 5x16 screw.
Standard 5x28 screw.
12-inch guide bar with Intenz feature.
12-inch low profile sawing chain.
Cover for the guide bar.
Chain tensioner component.
Screw for adjustment.
Black main pipe component.
Assembly for driveshaft guide.
Retaining ring component.
Guide for the shaft.
Foam pad component.
Aluminum rivet fastener.
A standard washer.
Upper part of the driveshaft.
Adapter for the upper driveshaft.
Assembly for bearing holder.
Steel rivet fastener.
Component that holds a bearing.
Ball bearing component.
A wave-shaped washer.
Large holder for an inner bearing.
Small holder for an inner bearing.
Assembly for a compression clamp.
Knob for securing components.
A standard screw for assembly.
A standard screw for assembly.
Upper collar for the main pipe.
Lower collar for the main pipe.
A locknut for securing.
Orange main pipe component.
Assembly for the ignition switch.
Standard 3x10 screw.
Knob for the switch.
Cover for the switch.
Assembly for the rear handle.
Right-side rear handle component.
Left-side rear handle component.
A standard screw for assembly.
A standard screw for assembly.
Spring for the throttle trigger.
The throttle trigger component.
Spring for the throttle trigger.
Lockout mechanism component.
Lockout for throttle control.
A collar component.
Straight pin of 3mm.
Assembly for floating bushing.
Floating bushing component.
Spring for floating bushing.
Caution warning label.
Cap for lower shaft tube adapter.
Half O-ring seal.
Adapter for lower shaft tube.
A standard screw for assembly.
Corrugated cover component.
The throttle control cable.
Standard 6mm nut.
Assembly for shoulder harness.
Assembly for a compression clamp.
Knob for securing components.
A standard screw for assembly.
A standard screw for assembly.
Upper collar for the main pipe.
Lower collar for the main pipe.
A locknut for securing.
Orange main pipe component.
Assembly for the ignition switch.
Standard 3x10 screw.
Knob for the switch.
Cover for the switch.
Assembly for the rear handle.
Right-side rear handle component.
Left-side rear handle component.
A standard screw for assembly.
A standard screw for assembly.
A locknut for securing.
Spring for the throttle trigger.
The throttle trigger component.
Spring for the throttle trigger.
Lockout mechanism component.
A standard washer.
Lockout for throttle control.
A collar component.
Straight pin of 3mm.
Assembly for floating bushing.
Floating bushing component.
Spring for floating bushing.
Caution warning label.
A locknut for securing.
Cap for lower shaft tube adapter.
Half O-ring seal.
Adapter for lower shaft tube.
A standard screw for assembly.
Corrugated cover component.
The throttle control cable.
Standard 6mm nut.
Assembly for shoulder harness.
The main driveshaft component.
Kit for connecting the driveshaft.
A pin for securing components.
Label indicating choke operation.
Label indicating choke operation.
Brand label for ECHO.
Label identifying the PPT-260 model.
Label identifying the PPT-261 model.
Caution warning label.
Hot caution warning label.
Gasket for the crankcase.
Gasket for the intake system.
Gasket for the intake system.
Gasket for the cylinder.
Gasket for the exhaust system.
Gasket for the exhaust system.
Heat shield for the exhaust system.
Combined socket wrench and screwdriver.
A standard socket wrench.
A bar used for locking.
An open-ended wrench.
A hexagonal bar tool.
A hexagonal key tool.
A Torx key tool.
A screwdriver tool.
A chuck key tool.
General