Outdoor Digital Timer
OPERATING INSTRUCTIONS
2. Reset
There is a reset hole under the dashboard.
Insert a pin or paperclip into the hole to reset
the timer. This will clear all programmed
settings.
Before initial use, plug the timer in for at least 30 minutes to charge the
internal battery. After the screen displays, the unit is ready for
programming.
The device must be mounted in a vertical position with the receptacle
facing downward and with the receptacle at least 2 ft above the
ground level.
1. Button Layout
1. MODE - Manual override and scroll
between the timer status options.
2. TIME - Press and hold for two seconds to
set current time.
3. PROG - Press and hold for two seconds to
begin setting function.
4. < + > - To increase time and day setting.
5. SET/ - Setting confirm and clear setting.
6. < - > - To reduce time and day setting.
7. RESET - Reset all the functions.
8. PHOTO SENSOR - The sensor will sense for light and dark, and
direct the timer to act accordingly.
3. Set Current Time
a. Press and hold "TIME" button for 2 seconds
to enter the current time settings. Press "+"
or "-" button to set the correct day.
b. Press the "SET" button to enter the hour
setting. Press "+" or "-" buttons to set the
current hour. Be sure that AM or PM appears
correctly.
c. Press the "SET" button to enter the minute
setting. Press the "+" or "-" buttons to set the
current minute.
d. Press the "SET" button to finish setting the current time and return to
normal display.
e. While setting those processes above, press and hold “SET” button
can clear the setting and back to the original timer settings. While
setting those processes above, press “TIME” button or wait for
15 seconds to back the standby display.
3
2
MODE TIME
PROG
+
-
SET/
1 2 3
4
6
8
8
5
1
4. MODE Setting
Press “MODE” button to choose the desired
mode.
ON→OFF→RDM Timer→AUTO Timer→
AUTO CDS→AUTO CDS + TIMER as
following listed.
The below icons will appear on the right of
display.
4
4-1
1. ON - Always on
The outputs remain always on.
4-2
2. OFF - Always off
The outputs remain always off.
4-3
3. RDM - Security feature.
On at a random time, and remains ON for
15 minutes.
Up to 5 on/off events every day.
The on/off events are built into this
product, turn ON at a random time and
the ON time is different each day,
creating a more “lived-in” look.
4-4
4. AUTO - ON/OFF program at AUTO mode.
ON/OFF at your exact programmed time.
4-5
5. AUTO - Photocell
ON at dusk, OFF at dawn.
4-6
6. AUTO - Program and Photocell
On at dusk, OFF at your exact
programmed time.
5. Program Setting
Make sure the current mode is at AUTO
mode, then press and hold "PROG" button for
two seconds to begin program setting, using
the "+" and "-" buttons to adjust the setting.
1. Press the "+" or "-" button to set the
correct day.
MO, TU, WE, TH, FR, SA, SU, MO TU WE TH FR, SA SU, MO TU
WE TH FR SA SU (cycle).
2. Press the "SET" button to enter the hour setting. Press "+" or "-"
buttons to set the desired hours for your timer to turn on. Be sure
that AM or PM appears correctly.
3. Press the "SET" button to enter the minute setting. Press the "+" or
"-" buttons to set the desired minutes for your timer to turn on.
4. Press “SET” button to enter the program OFF setting, the “1 OFF”
will appear on the display. Repeat steps 1 to 3 to set your desired
OFF time, up to 8 on/off programs settings.
5. While setting the programs, press and hold the “SET” button to
clear the set program time.
6. Once you complete the programs settings, press the “TIME” button
or wait for 15 seconds to restore your programs to back the
standby display.
5
6. Photocell Setting
Press the “MODE” button to select the
photocell function. This setting will
automatically turn the power on at dusk and
turn the power off at dawn.
6
7. Program and Photocell Setting
1. Press “MODE” to select “AUTO Program and photocell setting”,
then press and hold the “PROG” button for two seconds to set the
off time.
TM-108 Size: 145x210mm
Front
To Next Page
Need help?
General