To Next PageTo Next Page
Need help?Do you have a question about the Ecopia HMS-300 and is the answer not in the manual?
General| Brand | Ecopia |
|---|---|
| Model | HMS-300 |
| Category | Measuring Instruments |
| Language | English |
Identifies front panel components of the Hall Effect Measurement System.
Identifies back panel components of the Hall Effect Measurement System.
Illustrates and names components of the magnet set.
Details connecting the AC power cable to the main unit.
Explains connecting the main unit to a PC via RS232.
Explains connecting the main unit to a PC via USB.
Details connecting the sample cable to the main body and magnet set.
Guides installation of the measurement software from CD-ROM.
Notes the requirement for liquid nitrogen for 77K measurements.
Details RS232C connection setup and port confirmation.
Shows the software installation file extraction progress.
Indicates successful software installation and prompts for reboot.
Displays the main interface of the Hall Effect Measurement System software.
Instructs to set the rear switch to USB for connection.
Guides connecting the USB cable and initiating the hardware setup wizard.
Configures search options for installing the USB driver.
Shows the wizard searching for the USB driver.
Shows the wizard installing the USB driver software.
Confirms the completion of the USB driver installation.
Welcomes the user to the USB Serial Port installation wizard.
Guides selection of driver search locations for the USB Serial Port.
Shows the wizard searching for the USB Serial Port driver.
Shows the wizard installing the USB Serial Port driver files.
Confirms the completion of the USB Serial Port driver installation.
Guides checking the installed USB Serial Port via My Computer properties.
Accessing Device Manager through System Properties.
Navigating to Ports (COM & LPT) in Device Manager.
Displays properties of the installed USB Serial Port.
Shows general and port settings for the USB Serial Port.
Configures advanced settings like FIFO buffers for the COM port.
Guides selection of the correct COM port number for the device.
Shows files related to USB driver deletion.
Initiates the USB driver uninstallation process.
Confirms the completion of the USB driver uninstallation.
Shows the initial screen of the Hall Effect Measurement System software.
Explains the function of the 'START MEASUREMENT' and 'EXIT' buttons.
Details input fields for measurement parameters like date, user, sample name, etc.
Displays the raw measurement data collected by the system.
Shows the calculated results derived from the measurement data.
Explains the function of the HELP button.
Describes navigating to the I-V Curve window.
Explains the Comm. Test function for checking system connection.
Describes starting measurement after inputting values.
Explains saving measured data and results.
Describes recalculating results based on changed data.
Explains toggling between measuring and stopping.
Describes clearing measurement data and results.
Explains printing screen contents.
Describes exiting the program.
Details input fields for I-V measurement parameters like current, temperature, etc.
Shows the overall composition of the I-V measurement software screen.
Shows hall voltage change versus applied current as a graph.
Shows sheet resistance change as applied current as a graph.
Displays the raw data results from the I-V curve measurement.
Save measured data and results value.
Recursion existingly saved graph data.
Get the graph into line and regraph it again.
Toggle between STOP operating when measuring, and CONTINUE measuring when stopped.
Clear measurement data and results value.
Print the screen contents.
Program ending.
Open the "Help" window.
Details the procedure for preparing and bonding the sample for measurement.
Illustrates acceptable and not recommended methods for sample bonding.
Guides inserting the Sample Board into the magnet set.
Initial step to launch the measurement software.
Verifies system connection and communication readiness.
Entering current range, input values, magnetic flux density, and sample thickness.
Describes using the 'Measure' button and expected outputs.
Guides magnet insertion and subsequent measurements.
Advises on using standard AC outlets and handling the magnet safely.
Emphasizes keeping the sample clean and following safety procedures.
Warns against adverse environmental conditions and unauthorized repairs.
Details fuse replacement procedures and specifications.
Lists the technical specifications of the Hall Effect Measurement System.
Details software requirements and measured parameters.
Lists all components included with the Hall Effect Measurement System.
Outlines compensation policies for various types of product damage.
Provides contact details for Ecopia, the manufacturer.
