Eden London Arbor User Manual

Check Box for These Contents
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346, ext #20 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Arches (2)
2. Arch Rafters (5)
3. Post Caps (4)
4. Left Posts (2)
5. Right Posts (2)
6. Side Panel Top Horizontal Rails (2)
7. Side Panel Bent Vertical Spindles (4)
56.448 in.
8. Side Panel Middle Straight Vertical Spindles (2) 55.375 in.
9. Side Panel Middle Horizontal Rail (2)
10. Side Panel Bottom Horizontal Rail (2)
11. Ground Anchoring Stakes (4)
12. 1 1/4 in (3.17cm) Self Augering Screws (34)
Tools You Will Need
s#ORDLESS$RILL
s,EVEL
s3TOOLOR3HORT,ADDER
s3HOVEL
Assembly Time
s!PPROXIMATELYMINUTES(2 People)
General Information
Read Instructions through carefully before beginning assembly.
s7HENASSEMBLINGCOMPONENTSPLACEONANONABRASIVESURFACE
(i.e. shipping box) to avoid scratching.
s7ERECOMMENDANAREAAPPROXFTXFTFORUNOBSTRUCTEDASSEMBLING
s9OUSHOULDNOTNEEDTOUSEEXCESSIVEFORCEWHENASSEMBLINGCOMPONENTS
The London Arbor
Please read through before starting assembly.
IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.
ASSEMBLY INSTRUCTIONS
1
Not to Scale
7
6
5
4
2
3
1
42 in
CM
45 in
114.3 cm
IN
45.7 cm
21 in
53.3 cm
IN
219.7 cm
IN
CM
11 in
27.9 cm
56 in
142.2 cm

9

11
12
6ER/CT

Eden London Arbor Specifications

General

Brand	Eden
Model	London Arbor
Category	Outdoor Furnishing
Language	English

Summary

ASSEMBLY INSTRUCTIONS The London Arbor

Check Box for These Contents

Lists all parts included in the package for the London Arbor assembly.

Tools You Will Need

Lists the required tools for assembling the London Arbor, including a drill and level.

Assembly Time

Provides an estimated time of approximately 30 minutes for two people to assemble the arbor.

General Information

Offers crucial advice for assembly, such as using a non-abrasive surface and avoiding excessive force.

STEP ONE Assemble the Arch System

Step 1: Layout and Insert Arch Rafters

Layout one arch and insert the five arch rafters as illustrated.

Step 2: Guide and Insert Opposite Arch

Holding the opposite arch, guide the arch rafters into the routed holes.

Step 3: Fasten Arches to Rafter

Fasten the arches to the top rafter using 1 1/4 in. screws.

STEP TWO Assemble the Side Panels

Step 1: Insert Straight Vertical Spindle

Layout bottom rail and insert the middle STRAIGHT Vertical Spindle.

Step 2: Insert Bent Vertical Spindles

Insert the two vertical spindles that will be BENT into place.

Step 3: Attach Middle Horizontal Rail

Slide the Side Panel Middle Horizontal Rail over the three vertical spindles.

Step 4: Attach Top Horizontal Rail

Position the Side Panel Top Horizontal Rail and insert the Middle Vertical Spindle.

Step 5: Tension and Secure Side Panel

Tension bend the two outer vertical spindles; hold panel until inserted into post.

STEP THREE Connect Arch System to Side Panels

Step 1 & 2: Position Side Panels and Arch

Set out side panels ensuring post holes face outwards, insert assembled arch through top post holes.

Step 3: Adjust Opening Width

Adjust the opening to 42 inches between the posts for desired width.

Step 4: Fasten Arch System to Posts

Fasten the arch system to the posts by installing four screws at each post.

Step 5: Place Post Caps

Place the post caps on top of the posts to complete the assembly.

STEP FOUR Arbor Installation

A Into Earth for Temporary Installation

Instructions for securing the arbor temporarily into the ground using provided anchors.

Step 1: Move and Mark Arbor Location

Move the arbor to its final location, mark post positions, and lay it on its side.

Step 2: Excavate and Position

Excavate holes for anchors and carefully move the arbor back into position, leveling it.

Step 3: Drive Anchors and Backfill

Drive ground anchoring stakes through post holes and backfill with excavated soil.

B Into Earth For Permanent Installation

Guidance for permanently installing the arbor into the ground for increased security.

Step 1: Extend Posts with Lumber

Extend posts with pressure-treated lumber, shaved to 1 1/4 in. square and 46 in. long.

Step 2: Insert Wood into Posts

Insert wood extensions into the bottom of all four posts until they hit the bottom rail.

Step 3: Fasten and Install

Fasten wood extensions with screws and install directly into ground or concrete footing.