What to do if my EINHELL Bavaria BHR 130 Pressure Washer pump doesn't run?
If the electric pump of your EINHELL Bavaria Pressure Washer doesn't run when you press the switch, the plug may be damaged, there might be insufficient voltage, the pump could be locked, or the thermal relay may have triggered. Check the plug and fuses to ensure they are working. Manually turn over the motor. Allow the motor to cool down.
Why is there a loss of pressure in my EINHELL Bavaria BHR 130 Pressure Washer?
A loss of pressure in your EINHELL Bavaria Pressure Washer can occur if the nozzle is worn, the valves are dirty or clogged, the valve seals are worn, the seals are worn, or the filter is clogged. Try changing the nozzle. Check, clean, or exchange the valves. Check and/or exchange the valve seals and seals. Check and/or clean the filter.
How to fix no pressure in my EINHELL Bavaria BHR 130 Pressure Washer?
If the electric pump runs but no pressure is generated in your EINHELL Bavaria Pressure Washer, the intake filter may be clogged, air could be drawn in at the connectors, the inlet and outlet valves might be clogged or worn, or the nozzle hole diameter might be too large. Clean the filter. Inspect the intake connection fitting and hose connectors. Clean or replace the valves. Check and replace if necessary.
Why does my EINHELL Bavaria BHR 130 motor suddenly stop?
The motor of your EINHELL Bavaria Pressure Washer might suddenly stop because the thermal relay has triggered due to overheating. Check the voltage. Turn off the switch and let the motor cool down for a few minutes.
Why is my EINHELL Bavaria Pressure Washer making excessive noise?
Excess noise in your EINHELL Bavaria Pressure Washer could be due to air being drawn in, worn, dirty or clogged valves, worn bearings, high water temperature, or a dirty filter. Here are some things you can do: * Check the intake lines. * Check, clean, and exchange the valves. * Check and/or exchange the bearings. * Lower the water temperature to below 60 °C. * Check and/or exchange the filter.
What causes irregular operating pressure in my EINHELL Bavaria BHR 130?
Irregular operating pressure in your EINHELL Bavaria Pressure Washer can be caused by air being drawn in, clogged and worn valves, or worn seals. Check the intake connectors. Clean and replace the valves. Check and replace the seals.
Why is water leaking from the pump head of my EINHELL Bavaria Pressure Washer?
If water is leaking from the pump head of your EINHELL Bavaria Pressure Washer, it could be due to worn seals or a worn O-ring in the seal set. Exchange the seal. Exchange the O-ring.
What to do if my EINHELL Bavaria BHR 130 Pressure Washer motor hums but doesn't start?
If your EINHELL Bavaria Pressure Washer motor hums but doesn't start when the switch is pressed, the mains voltage might be lower than specified, the pump could be blocked or frozen, or the extension cable may be insufficient. Check to see that the extension cable is sufficient. Exchange the extension cable for one that is sufficient.
Why is my EINHELL Bavaria Pressure Washer pump dripping?
The pump of your EINHELL Bavaria Pressure Washer may be dripping because the seals are worn. Check and replace the seals (professional repair shop).
Why is the water expelled from my EINHELL Bavaria Pressure Washer mixed with oil?
If the water expelled from your EINHELL Bavaria Pressure Washer is mixed with oil, the sealing rings (water + oil) are likely worn. Check and/or exchange them.
Explains the components shown in Figure 1 of the device.
Details the steps for assembling the high-pressure cleaner.
Instructions on how to safely start and operate the high-pressure cleaner.
Guide on how to fill and use the detergent tank for cleaning.
Provides tips and recommendations for using the high-pressure cleaner correctly.
Instructions for checking and cleaning the water intake filter.
Procedures for safely disposing of the machine at the end of its life.
General| Brand | EINHELL Bavaria |
|---|---|
| Model | BHR 130 |
| Category | Pressure Washer |
| Language | English |
To Next Page