EasyManua.ls Logo

EINHELL TC-PT 2500 - User Manual

EINHELL TC-PT 2500
80 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
TC-PT 2500
Art.-Nr.: 20.225.30 I.-Nr.: 11016
7
D Originalbetriebsanleitung
Palettenhubwagen
GB Original operating instructions
Pallet Lifting Truck
I Istruzioni per l’uso originali
Transpallet
S Original-bruksanvisning
Palldragare
FIN Alkuperäiskäyttöohje
Paletinsiirtovaunu
P Manual de instruções original
Carro elevador de paletes
HR/ Originalne upute za uporabu
BIH Kolica za podizanje paleta
GR Πρωτότυπες Οδηγίες χρήσης
Aνυψωτικό για παλέτες
CZ Originální návod k obsluze
Paletový vozík
SK Originálny návod na obsluhu
Paletový vozík
H Eredeti használati utasítás
Palettaemelőkocsi
SLO Originalna navodila za uporabo
Dvigalo za palete
Anl_TC_PT_2500_SPK7.indb 1Anl_TC_PT_2500_SPK7.indb 1 10.04.2019 15:00:5110.04.2019 15:00:51

Table of Contents

Questions and Answers

  • B
    Brian StoneAug 10, 2025
    Why won't the lifting forks on my EINHELL TC-PT 2500 Trucks raise?
    • M
      Michelle MitchellAug 10, 2025
      The lifting forks on your EINHELL Trucks might not raise due to several reasons: * There may be no hydraulic oil. If this is the case, fill in hydraulic oil. * The hydraulic oil might be dirty, requiring a change. * The setting nut (K) could be too high. To resolve this, set the setting nut (K) according to section 7. * There may be air in the hydraulic unit. If so, vent the hydraulic unit as described in section 8.
  • I
    Ian DelgadoAug 16, 2025
    What to do if the lifting forks on my EINHELL Trucks descend without the relief valve working?
    • G
      gthorntonAug 16, 2025
      If the lifting forks on your EINHELL Trucks descend without the relief valve working, it could be due to several factors: * The hydraulic oil may be dirty, so change the hydraulic oil. * The hydraulic module could be defective, requiring replacement. * There might be air in the hydraulic unit; vent it as described in section 8. * The seals may be worn or damaged, necessitating replacement. * The setting nut (K) may be set incorrectly; adjust it according to section 7.
  • E
    Eric BrownAug 22, 2025
    How to fix leaks on my EINHELL TC-PT 2500 Trucks?
    • P
      Penny WolfAug 22, 2025
      Leaks on your EINHELL Trucks can be attributed to: * Worn or damaged seals. If this is the cause, replace the seals. * A defective hydraulic module. In this case, replace the hydraulic module.
  • K
    Katrina HolmesAug 28, 2025
    What to do if the lifting forks on my EINHELL TC-PT 2500 Trucks cannot be lowered?
    • C
      Cynthia GomezAug 28, 2025
      If the lifting forks on your EINHELL Trucks cannot be lowered, it may be because: * The piston rod or pump housing has been damaged by overloading or an uneven load distribution, so replace the piston rod or pump housing. * The piston is stuck, so replace the piston. * The setting nut (K) is set wrongly, so set the setting nut (K) according to section 7.
  • M
    Mitchell DaySep 3, 2025
    Why can't the lifting forks on my EINHELL TC-PT 2500 be raised to the maximum height?
    • S
      samuel49Sep 3, 2025
      If the lifting forks on your EINHELL Trucks cannot be raised to the maximum height, it may be because there is too little hydraulic oil. If this is the case, fill in hydraulic oil.

EINHELL TC-PT 2500 Specifications

General IconGeneral
BrandEINHELL
ModelTC-PT 2500
CategoryTrucks
LanguageEnglish