EINHELL TE-SG 18/10 Li User Manual (English)

Other manuals for EINHELL TE-SG 18/10 Li

Original Operating Instructions197 pages

Questions and Answers:

J
Jacob PhillipsJul 28, 2025
What to do if there is no sealant coming out of my EINHELL Food Saver?
- J
  Jennifer PadillaJul 29, 2025
  If no sealant or adhesive is coming out of the cartridge nozzle of your EINHELL Food Saver, several factors could be at play. First, ensure that the cartridge is open. If it is, check for hardened material blocking the nozzle or cartridge opening; remove any obstructions, using the piercing tool if needed. A damaged or empty cartridge can also cause this issue, so inspect the cartridge and replace it if necessary. Lastly, a jammed piston rod could be the culprit; in this case, dismantle and clean the piston rod.
A
Alec BellAug 2, 2025
Why is my EINHELL TE-SG 18/10 Li Food Saver dispensing too little sealant?
- C
  Chris HaleAug 3, 2025
  If your EINHELL Food Saver is dispensing too little sealant or adhesive, the opening in the cartridge nozzle may be too small. Try cutting the cartridge nozzle to a larger size or replacing it altogether. Also, check the feed speed setting; if it is set too low, increase it. Finally, the sealant or adhesive itself may be solid; if this is the case, replace the cartridge.
J
Jackie MullinsAug 7, 2025
How to fix excessive sealant dispensing from EINHELL Food Saver?
- J
  Jacqueline FloresAug 8, 2025
  If your EINHELL Food Saver is dispensing too much sealant or adhesive, the opening in the cartridge nozzle might be too large. You can address this by cutting the cartridge nozzle to a more appropriate size or replacing it. Additionally, the feed speed setting could be too high; try lowering it to reduce the amount of sealant dispensed.
T
Todd BrownAug 12, 2025
What to do if there is no sealant or adhesive at the EINHELL Power Tool cartridge nozzle?
- A
  Allison GreenAug 12, 2025
  If there's no sealant or adhesive coming out of the EINHELL Power Tool cartridge nozzle, first ensure that the cartridge is open. If the cartridge nozzle or opening has hardened material, remove it, using the piercing tool if needed. A damaged cartridge should be replaced. If the piston rod is jammed, dismantle and clean it. Finally, if the cartridge is empty, replace it with a new one.
J
jacksonkaraAug 17, 2025
Why is there too much sealant or adhesive at the EINHELL Power Tool cartridge nozzle?
- J
  Jessica HillAug 17, 2025
  If you're getting too much sealant or adhesive from the EINHELL Power Tool cartridge nozzle, the opening in the cartridge nozzle might be too large. Try cutting the cartridge nozzle to a smaller size or replacing it. Also, the feed speed might be set too high; adjust it to a lower setting.
J
Jonathan McdonaldAug 23, 2025
What to do if too little sealant or adhesive at the EINHELL Power Tool cartridge nozzle?
- T
  tmooreAug 23, 2025
  If too little sealant or adhesive is coming out of the EINHELL Power Tool cartridge nozzle, the opening in the cartridge nozzle might be too small; cut it to a larger size or replace it. The feed speed might also be set too low, so increase it. If the sealant or adhesive is solid, replace the cartridge.

EINHELL TE-SG 18/10 Li Specifications

General

Type	-
Volume	310 ml
Product color	Black, Red
Suitable for indoor use	Yes
Battery voltage	18 V
Battery pack	No
Quantity per pack	1 pc(s)
Package depth	290 mm
Package width	435 mm
Package height	80 mm
Package weight	2440 g