GB
- 10 -
5.3 Fitting the tank bag (Fig. 18)
Fit the dirt bag (Fig. 3/27) as shown in Figure 18.
5.4 Fitting the suction hose (Fig. 1-3/18)
Connect the suction hose (9) to the correspon-
ding connector on the wet and dry vacuum clea-
ner, depending on the application required.
Vacuuming
Connect the suction hose (9) to the suction hose
connector (8).
Blowing
Connect the suction hose (9) to the blow connec-
tor (19).
Air regulator (Fig. 3/29)
The air regulator (29) can be fi tted between the
suction hose (9) and the suction tube (17). The
suction power of the nozzle can be infi nitely ad-
justed using the air regulator (29).
When wet vacuuming, make selective use of the
air regulator to suck in air as well as liquids. This
will help to take some strain off the equipment
when vacuuming liquids.
5.5 Suction nozzles
Dual-purpose nozzle (Fig. 3)
The dual-purpose nozzle (14) is for vacuuming
solids and liquids over medium to large areas.
Various attachments can be fi tted to the combi-
nation nozzle depending on what you sort of work
you wish to carry out:
Crevice nozzle (Fig. 3)
The crevice nozzle (23) is designed for vacu-
uming solids and liquids in corners, edges and
other areas that are diffi cult to access.
Upholstery nozzle (Fig. 3)
The upholstery nozzle (26) is specially designed
for vacuuming solids on upholstery and carpets.
6. Operation
6.1 ON/OFF switch (Fig. 1/7)
Switch position 0: Off
Switch position I: Normal operation
Switch position AUTO: Automatic mode
6.2 Dry vacuuming
Use the pleated fi lter (24) for dry vacuuming (see
point 5.2). The dirt bag (27) can be fi tted in additi-
on when removing particularly stubborn dirt (see
point 5.3).
If you want to suction large amounts of fi ne dust,
you can use the coarse fi lter (16) (see section 5.2
Fitting the coarse fi lter).
Always ensure that the fi lters are perfectly secure.
6.3 Wet vacuuming
For wet-vacuuming, use the foam fi lter (25) (see
point 5.2).
For wet suctioning, fi t the sealing ring (37) (see
section 5.2 Fitting the sealing ring).
Check that the fi lter is securely fi tted at all times.
Water drain screw (Fig. 1/11)
To make the tank (10) easier to empty after wet
vacuuming, it is fi tted with a water drain screw
(11). Open the water drain screw (11) by turning it
anti-clockwise and drain the liquid.
To empty the container completely and easily, ap-
ply the castor brake (3) and tilt the container.
When wet vacuuming, the fl oating safety switch
(Fig. 2/21) closes when the maximum tank level
is reached. In doing so, the suction noise of the
equipment will change and become louder.
You must then switch off the equipment and em-
pty the tank.
Danger!
The wet and dry vacuum cleaner is not suitable
for the vacuuming of combustible liquids.
For wet vacuuming, use only the supplied foam
fi lter.
6.4 Automatic mode (Fig. 1)
Connect the power cable on your electric tool to
the automatic socket-outlet (4) and connect the
suction hose (9) to the extractor connector on
your electric tool. Check that the connections are
secure and air-tight.
Anl_TE_VC_2350_SACL_UKCA_SPK7.indb 10Anl_TE_VC_2350_SACL_UKCA_SPK7.indb 10 11.01.2022 10:17:3311.01.2022 10:17:33
To Next Page
Loading...
Need help?
General
