Eleaf iStick Pico - User Manual

*Important notice*
To avoid overheating we recommend to turn off the device while transporting. Always
use compatible chargers provided.
The Eleaf Pico is a tiny but very powerful unit operating between 1 watt to 70 watts or 200 to 600 F. It works ideally
with the top filling Melo III Mini tank and the supplied 0.3 ohm coils deliver excellent vape and taste. Powered by a
single, interchangeable, 18650 battery it can be set to Variable Wattage (VW), Bypass, and Temperature Controlled
(TC) modes and can be used with Nickel 200 (Ni), Titanium (Ti) and Stainless Steel 316 (SS) M1,M2,M3.
For the expert vaper there is the Temperature Coefficient of Resistance (TCR) mode which allows the devise to
support different temperature control coils. These are under the modes M1, M2 and M3. These modes allow for
alternate Coils to be used (includes re-buildable for the more experienced Vaper) these modes are not needed when
using Eleaf coils provided with the kit or the Eleaf temperature control Nickel coils.
The kit includes:
1 X iStick Pico (18650, 2500mah, batteries sold separately)
1 X Melo III Mini tank – 2ml, top fill, with 0.5 coil and spare 0.3 ohm coil
1 x USB charger
1 x User Manual
How to use:
Note: 1) Ensure you use a high-
rate 18560 cell whose
continuous discharge current
should be above 25 amps.
2) Do not use a cell which has a
torn casing as this can be
dangerous.
3) Before using the Pico set the
wattage to the appropriate
level suitable to the coil
resistance in the clearomiser.
Stealth on/off: To turn off the OLED screen, but still vape, press the fire button and down button simultaneously.
You can press the fire button once to see current setting. This will increase the battery life.
Lock/unlock: Press and hold for 2 seconds the “up” and “down” buttons to lock the unit and repeat to unlock.
To change the orientation of the OLED when the unit is powered off press the “up” and “down” buttons for 2
seconds.
Switching vape modes: With the unit powered on, press the fire button 3 times in quick succession, the OLED will
display the current vaping mode. Press the “up” or “down” button to scroll through the various modes - Variable
Wattage, Bypass, TC –Ni, TC-Ti, TC-SS, TCR-M1, TCR-M2 and TCR-M3. To select a mode press the fire button once.

Summary

Eleaf Pico Device Operation

Stealth On;Off Function

Turns off the OLED screen while allowing vaping to conserve battery life.

Lock and Unlock Device

Press and hold the 'up' and 'down' buttons for 2 seconds to lock or unlock the unit.

Switching Vape Modes

Press the fire button 3 times to cycle through Variable Wattage, TC, and TCR modes.

Eleaf Pico Operating Modes Explained

Variable Wattage (VW) Mode

Supports coils from 0.1ohm to 3.5ohm; adjust wattage for optimal vape and taste.

Bypass Mode Operation

Bypasses safety features for direct output, suitable for experienced vapers.

Temperature Control (TC) Modes

Supports Ni, Ti, SS coils within temperature ranges of 100-315F or 200-600C.

Eleaf Pico Safety, Charging, and Advanced Features

Device Safety Features

Covers Atomiser Protection, Low Atomiser Alert, Low Voltage, and Temperature Protection.

Battery Charging Information

Battery indicator flashes below 10% power and goes out when fully charged.

Temperature Coefficient of Resistance (TCR)

Mode for experts to adjust for different coil wires using M1, M2, M3 settings.

Eleaf iStick Pico Specifications

General

Output Wattage	1-75W
Temperature Range	100-315°C / 200-600°F
Resistance Range (TC modes)	0.05-1.5 ohm
Resistance Range (VW/Bypass mode)	0.1-3.5 ohm
Dimensions	45mm x 23mm x 70.5mm
Thread Type	510
Display	OLED
Output Voltage	0.5-9V
Battery Capacity	18650 (not included)
Modes	VW, Bypass, TC (Ni, Ti, SS), TCR
Charging	Micro USB
Color Options	Black, Silver, White, Pink