Electrolux EBR3216 - Cleaning and Care; Blender Cleaning Procedures; Troubleshooting; Common Issues and Solutions

6
www.electrolux.com
CNT
CNS
KR
ID
TH
VN
EN
10.Whentheingredientshavebeenground/choppedtothedesiredconsistency,unplugtheappliance,
andremovethegrinderfromtheappliance.NOTE:Donotremovethegrinderbowldirectlyfromthe
motor base as this will cause the ingredients to spill out and expose the blade assembly.
11.Turnthegrinderupsidedownandcarefullyremovethebladeassemblybyturningitanti-clockwise.
Remove the ingredients and wash the grinder bowl (L) and blade assembly (M) in soapy water
immediately after use.
CLEANING AND CARE
12.Quick cleaning:Pourwarmwaterintothejug(D)upto750ml,addafewdropsofdetergent.Replace
thelidandoperatetheblenderforafewsecondsbyturningthespeedselector(H)tothePULSE
position briefly. Finally, remove the jug and rinse it under running water.
13. Thorough cleaning: Switch off the blender and unplug the power cord. Remove the jug (D) from the
motor base (G).
13a.Cleaning the motor base: Wipethemotorbasewithadampcloth.Never immerse the motor
base in water or clean it under running water!
13b.Cleaning the jug: Removethelid(B)andjug(D).Turnthebladeassembly(F)clockwiseand
remove it by pulling it down. Rinse the blade assembly in water and detergent. Caution! Handle
carefully, the blades are very sharp!
 Thelid,jugandmeasuringcupcanbewashedinthedishwasher.Becarefulwhenre-assemblingthe
bladeassembly.Pleasesee“Gettingstarted”section,no.1forinstructionsonbladeassembly.
* Specifications vary by model
TROUBLESHOOTING
Symptom Cause Solution
Theblenderdoesnot
start.
Thecomponentsarenotxed
properly.
Check if all the components are properly
locked into position.
Thespeedselector(H)isnoton
the right position.
Choosetheappropriatespeed.Touse
PULSEfunction,makesurethespeed
selector(H)isonPULSEposition.
Thejug(D)isoverlled.
Reduce the content in the jug (D) so you do
not exceed the maximum level.
Theplugisnotproperly
connected to the power outlet.
Check the connection of the plug to the
outlet or try another outlet.
Power outage. Waituntilpoweroutageisover.
Functional problem. Contact authorized service center.
Check the circuit breaker*.
Whentheelectriccurrentis
over the setting value of the
current restorer, it will disconnect
immediately.Thisisasafety
feature.
Torestart,switchotheblenderandunplug
the power cord, allow the appliance to cool
down, and then press the red salient point.
Thenputtheplugbackintothewallsocket
and switch the appliance on again.
(RefertoFig.14)
Contents leaks from the
lid (B).
Thejug(D)isoverlled.
Reduce the content in the jug (D) so you do
not exceed the maximum level.
Thelid(B)isnotcorrectly
positioned.
Lock the lid (B) correctly on the blender
jug (D).
Leak from the base of
the blender jug (D).
Therubberseal(E)isnot
positioned correctly or is missing.
Repositiontherubberseal(E)ontheblade
assembly (F) and lock it correctly onto the
jug (D).
Thebladedoesnotturn
easily.
Pieces of food too large or too
hard.
Reducethesizeorquantityofingredients
andaddsomeliquid.