Need help?Do you have a question about the Electrolux EID200QSW00 and is the answer not in the manual?
General| Brand | Electrolux |
|---|---|
| Model | EID200QSW00 |
| Category | Dryer |
| Language | English |
Defines WARNING, CAUTION, NOTE, and IMPORTANT terms used in the manual for safety.
Describes the main control system components, including the UI and Main Control Boards.
Explains the User Interface board's function and button layout.
Details the functions of the Main Control Board, including sensing and control.
Provides schematic diagrams for control board connections and wiring.
Illustrates the wiring connections for the main control board.
Shows the schematic diagram of the user interface board connections.
Presents the overall wiring diagram of the appliance.
Lists electrical components with their resistance and specifications.
Step-by-step guide to disassemble and access the control panel.
Detailed steps to disassemble and assemble the anti-interfer filter.
Instructions for disassembling and assembling the drum vanes.
Steps to disassemble and reassemble the main control board.
Instructions for accessing and replacing the temperature probe (NTC).
Detailed steps for disassembling and assembling the motor assembly.
Instructions for disassembling and assembling the motor and fan wheels.
Guide to disassembling and reassembling the heater assembly.
Instructions for disassembling and assembling the pump.
Steps for disassembling and assembling the fluff filter.
Guide to disassembling and assembling the condenser assembly.
Instructions for accessing and replacing the humidity sensor.
Steps for disassembling and assembling the door latch mechanism.
Guide to disassembling and replacing the drum lamp.
Instructions for disassembling and assembling the door switch.
Steps for disassembling and assembling the drive belt.
Instructions for disassembling and replacing the leveling leg.
Steps to enter the appliance's diagnostic mode.
Guide on navigating through available diagnostic tests.
Procedure to clear stored error codes from the system.
Instructions on how to exit the diagnostic mode.
Steps to perform a factory default reset of the appliance.
Explanation of the appliance's demo mode and its types.
Detailed steps to activate the appliance's demo mode.
Instructions to clear the demo mode and return to normal operation.
List of error codes, their full names, and corresponding page numbers.
Troubleshooting steps for the Condense Pump Error (0x21).
Troubleshooting steps for the Condense Pump Sensing Error (0x22).
Troubleshooting for Conductimetric Sensor Frequency Too High (0x31).
Troubleshooting for Conductimetric Sensor Frequency Too Low (0x32).
Troubleshooting steps for the Door Closed Sensing Error (0x45).
Troubleshooting steps for the FCV Safety Error (0x55).
Troubleshooting for FCV Motor Plug Not Connected (0x56).
Troubleshooting for FCV Current Trip Failure (0x57).
Troubleshooting for FCV Over Current Failure (0x58).
Troubleshooting for FCV Board Overheating (0x5A).
Troubleshooting steps for the FCV Motor Not Following error (0x59).
Troubleshooting for FCV Under Voltage Failure (0x5B).
Troubleshooting for FCV Over Voltage Failure (0x5C).
Troubleshooting for FCV Unknown Message Error (0x5D).
Troubleshooting for FCV Power Module Error (0x5F).
Troubleshooting for Heater Short Circuit Error (0x62).
Troubleshooting for Heater Error (0x63).
Troubleshooting steps for the Heater Sensing Error (0x64).
Troubleshooting steps for the Drying NTC Error (0x71).
Troubleshooting steps for the Heater NTC Error (0x72).
Troubleshooting steps for the Steamer NTC Error (0x73).
Troubleshooting for Selector Position Code Error (0x83).
Troubleshooting for Selector Configuration Table Error (0x86).
Troubleshooting for UI Board Microcontroller Self Test Failure (0x87).
Troubleshooting for User Interface Communication Error (0x91).
Troubleshooting for User Interface Protocol Incongruence Error (0x92).
Troubleshooting for Machine Configuration Checksum Error (0x93).
Troubleshooting for Cycle Configuration Checksum Error (0x94).
Troubleshooting for Missing Program on CTF Error (0x97).
Troubleshooting for User Interface Configuration Checksum Error (0x9C).
Troubleshooting for User Interface Touch Sensor Not Working (0x9E).
Troubleshooting for Power Supply Frequency Out of Range (0xB1).
Troubleshooting for Power Supply Amplitude Out of Range (0xB2).
Troubleshooting for Power Supply Amplitude Out of Range (0xB3).
Troubleshooting for Zero Watt Relay Error (0xB4).
Troubleshooting for Line Safe Short Circuit Error (0xBD).
Troubleshooting for Line Safe Error (0xBE).
Troubleshooting for Line Safe Sensing Error (0xBF).
Troubleshooting for Safety Reset Error (0xF6).
To Next Page