Electrolux Enviro Multi Steamer Plus User Manual

6
INSTRUCTIONS FOR USE:
Filling the boiler tank before use
Before unscrewing the tank cap, always ensure that the cleaner is switched off and disconnected from the power supply.
Unscrew safety cap (2) and, using funnel (28), POUR INTO THE TANK TWO MEASURES (27) OF WATER TO THE
LEVEL OF 500cc (FIG. A). Screw safety cap (2) back on again.
Turning on the appliance
To turn on the appliance, insert the power cord plug into an electrical socket and press ON/OFF switch (8); green indicator
(7) and amber indicator (6) will come on. As soon as amber indicator (3) goes out, the appliance is ready for use. Press
button (24) to supply steam. To prevent steam from being accidentally supplied, move the safety slider (23) to the ••
position.
When using the steam cleaner for the first time and to prevent water forming inside the tube, keep the gun higher than
cleaner body (9). In any case, both when first using the cleaner and every time it is left unused for a few minutes, press
steam supply button (24) and discharge any water that has formed in hose (26) into a container. Then, as soon as the
cleaner begins supplying steam only, direct the steam jet towards the floor and press steam supply button (22) at least two
or three times.
The Enviro Multi Steamer Plus is equipped with a steam regulation knob (3) which allows the quantity of steam to be
adjusted.
Reduce the steam pressure by rotating the knob to the right for cleaning textiles or delicate surfaces. Turn it to the left for full
power when cleaning stubborn grease, grime or fat from hard surfaces
Fitting accessories
Detachable flexible tube:
Insert the plug end of the flexible tube (26) into the socket of the appliance body (9), taking care that the arrow is to the top,
as shown in figure H.
Extension spout:
Insert the extension spout (21) by pushing it into the fixed section of the gun and aligning the groove in the spout with the
line on the gun. Align the spout groove with the line on the gun, then rotate the spout 90 degrees (clockwise) in the direction
of the arrow until it locks into place (fig. B).
Round brush and angled nozzle:
Both accessories can be fitted to the extension spout (fig. C) or the gun nozzle (fig. D).
Fabric brush with cloth and glass wiper:
The fabric brush (20) can be attached to gun nozzle (22). The brush can be fitted with glass wiper (19). Insert wiper side
hooks (E1) into brush tabs (E2) and join the two parts together (fig. E). The brush can also be fitted with a microfibre cloth
cover (18) for cleaning fabrics, sofas and mattresses (fig. F).
The microfibre cloth cover is woven from an extremely compact fibre (100 times finer than a human hair) which permits the
fibre to penetrate deep into surfaces in the home, picking up and eliminating every trace of dirt and grease, without the need
for detergents. Ensure that the tube is empty of all water before steam cleaning fabrics, sofas, etc.
Extension tubes:
To extend the reach of the appliance, gun nozzle (22) can be fitted with extension tubes (11) and glass cleaner connector
(15). Other accessories can then be attached depending on the work to be done.
Floor brush :
This accessory is used with the extension tubes
(11), and is provided with a floor cloth (12).
Insert the elbow inside the hole of the floor
nozzle, paying attention to line up the reference
symbol on the elbow and on the floor nozzle
as shown in the picture.Press the elbow up to
run, turn of 90¡ and connect the whole item to
the extension tubes.
To attach the cloth, rest the brush on it
and then pull the cloth projections one
by one under retaining springs (G1) as
shown in fig. G.

Electrolux Enviro Multi Steamer Plus Specifications

General

Brand	Electrolux
Model	Enviro Multi Steamer Plus
Category	Steam Cleaner
Language	English