Electrolux ESF6010BW User Manual (English)

Other manuals for Electrolux ESF6010BW

Questions and Answers:

T
Tammy GarciaAug 21, 2025
Why won't my Electrolux ESF6010BW fill with water?
- B
  Brandon PerezAug 22, 2025
  If your Electrolux dishwasher isn't filling with water, first, ensure the water supply is turned on. Check for low water pressure (it should be at least 20 PSI). Also, inspect the water fill valve and hose for any obstructions, cleaning them if necessary. Damaged wiring should be repaired, and defective components like the water fill valve, pressure switch, flowmeter, or PCB assembly should be replaced. Finally, minimize water usage elsewhere in your home when running the dishwasher.
A
Angela ClarkeAug 23, 2025
Why is my Electrolux ESF6010BW Dishwasher running but not heating?
- S
  smendezAug 23, 2025
  If your Electrolux dishwasher runs but doesn't heat, ensure the input voltage is at least 198V. Other potential issues include a defective thermal resistor, heating element, or micro-switch of the pressure switch assembly, all of which would need replacement. Damaged wiring should be repaired. Also, ensure there is enough water filling the dishwasher. If the water fill is insufficient, refer to the information about 'Too little water fill'. Finally, a defective PCB assembly may be the cause, requiring replacement.
E
Edward McdonaldAug 25, 2025
Why does my Electrolux ESF6010BW have poor drying of dishes?
- C
  Charles MorganAug 25, 2025
  If your Electrolux dishwasher isn't drying dishes well, ensure the dishes, pots, pans, and silverware are loaded correctly by consulting the owner's manual for proper loading techniques. Also, the dispenser might be defective and needs to be replaced.
L
lnortonAug 26, 2025
Why won't my Electrolux ESF6010BW Dishwasher start?
- D
  Diana WalshAug 26, 2025
  Your Electrolux Dishwasher might not start due to a few reasons. First, ensure that the power supply to the dishwasher is turned on and that the door is securely closed. Also, check if the power cord is properly plugged into the wall socket. These steps will help ensure your dishwasher starts correctly.
T
Theresa CervantesAug 27, 2025
How to reset Electrolux Dishwasher after a blown fuse?
- H
  Holly LeonardAug 27, 2025
  If your Electrolux Dishwasher has a blown fuse or a tripped circuit breaker, replace the fuse or reset the circuit breaker. Also, remove any other appliances that are sharing the same electrical circuit with the dishwasher to prevent overloading.
M
Melody JohnsonAug 29, 2025
What to do if my Electrolux ESF6010BW Dishwasher will not pump out?
- S
  Stacey WalkerAug 29, 2025
  If your Electrolux dishwasher isn't pumping out water, the drain pump might be defective and needs replacement. Another possible cause is an obstructed drain hose, which requires inspection. In some cases, a defective PCB assembly can also be the reason, requiring replacement.
S
Stephanie ThompsonAug 30, 2025
What to do if my Electrolux ESF6010BW Dishwasher does not work when I press start?
- J
  Jason GardnerAug 30, 2025
  If your Electrolux dishwasher isn't starting when you press the start button, make sure the door is fully closed. If that's not the issue, the door switch contacts or the door handle assembly might be defective and need replacement. Damaged wiring can also prevent the dishwasher from starting, so repair the wiring. In some cases, a defective PCB assembly can also be the reason, requiring replacement.
C
Christine BurtonSep 1, 2025
How to fix water leaks from Electrolux ESF6010BW?
- L
  larry89Sep 1, 2025
  If your Electrolux dishwasher is leaking water, the drain pump could be defective and need to be replaced, or the dishwasher might not be level and needs leveling. Check for loose hose clamps and tighten or replace them as necessary. Also, ensure the overflow cover is properly remounted and that the drain pump assembly is correctly seated with the sump. Defective flow system seals should be replaced. For issues related to too much water fill, refer to the information about that specific symptom. If soap suds are leaking, consult the use and care manual.
D
David NelsonSep 2, 2025
Why does my Electrolux ESF6010BW Dishwasher motor hum but not start?
- S
  simmonsscottSep 3, 2025
  If your Electrolux dishwasher motor hums but won't start or run, the motor bearings or motor capacitor might be defective and need replacement. Damaged wiring can also cause this issue and should be repaired. Also, ensure the motor voltage is correct; if it's not, the motor should be replaced.
M
Mr. Kenneth Parsons MDSep 4, 2025
Why does water remain in the bottom of my Electrolux ESF6010BW?
- S
  Steven McmillanSep 4, 2025
  If water remains in the bottom of your Electrolux dishwasher, note that a small amount of water in the sump area is normal to keep the pump primed. However, if there's excessive water, the drain pump or check plate might be defective and need replacement or cleaning. Also, the one way valve may be defective, requiring you to clean or replace the air breaker.