Electrolux EXD16DN4W - How to Use Timer Function; Fault Codes; Removing collected water

9ENGLISH
NOTE:
• TheDryermodemustbeoperatedina
closeroom,donotopenthedoorand
window.
• Tomakethebeste󰘯ective
dehumidi󰘰cation,please󰘰rstdehydrate
thewetclothes.
• Makesuretodirectair󰘱owatthewet
clothesshownaspicturebelow.
• Forthickandheavywetclothesmaynot
getthebeste󰘯ectivedehumidi󰘰cation.
CAUTION!
• Donotcovertheairoutletofthe
unitwithclothes.Itmaycause
excessiveheat,󰘰reorfailure
ofunit.
• Donotplacethewetclotheson
thetopoftheunitanddonot
makethewaterdropintothe
unit.Itmaycauseelectricshock,
creepageorfailureofunit.
4.7 HowtoUseTimerFunction
TheTIMERfunctionenablesyouto
eitherDelayStartorDelayStoptheunit
inthechoicefrom0.5hourto24hours.
Whentheunitison,presstheTimer
button,theTimerindicatorlight
illuminates.ItindicatestheAutoStop
programisinitiated.Whentheunitis
o󰘯,presstheTimerbutton,thetimer
indicationlightilluminates.Itindicatesthe
AutoStartisinitiated.
Pressorholdthe or padtochange
theAutotimeby0.5hourincrements,up
to10hours,thenat1hourincrementsup
to24hours.Thecontrolwillcountdown
thetimeremaininguntilstart.
Theselectedtimewillregisterin
5secondsandthesystemwill
automaticallyrevertbacktodisplay
theprevioushumiditysetting.
TurningtheunitONorOFFatanytime
oradjustingthetimersettingto0.0will
canceltheAutoStart/Stopfunction.
WhenLEDdisplaywindowdisplaysthe
codeofP2,theAutoStart/Stopfunction
willalsobecancelled.
NOTE:
• BeforeenteringTIMERsetting,make
surepowerisbeingsuppliedtotheunit.
• BeforeenteringTIMERsetting,make
surepressingHUMIDITYorbutton
setsonedesiredroomhumidity󰘰rst.
4.8 FaultCodes
AS-Humiditysensorerror--Unplugthe
unitandplugitbackin.Iferrorrepeats,
callforservice.
ES-Temperaturesensorerror--Unplug
theunitandplugitbackin.Iferror
repeats,callforservice.
P2-Bucketisfullorbucketisnotinright
position--Emptythebucketandreplace
itintherightposition.
4.9 Removingcollectedwater
Therearetwowaystoremovecollected
water.
Use the bucket
Whentheunitiso󰘯,ifthebucketisfull,
theunitwillbeep8timesandtheFull
indicatorlightwill󰘱ash,thedigitaldisplay
showsP2.
Whentheunitison,ifthebucketisfull,
thecompressorturnso󰘯andthefan
turnso󰘯after30secondsfordryingthe
waterofthecondenser,thentheunitwill
beep8timesandtheFullindicatorlight
will󰘱ash,thedigitaldisplayshowsP2.
Followthestepbelowtoremovethe
collectedwaterfromthebucket:
1. Griptheleftandrighthandlessecurely,
thenpulloutthebucketalittle.
2. Holdbothsidesofthebucketwitheven
strength,andpullitoutfromtheunit.