Spring
Lever
Cradle Assembly
Brackets
S
crew Used
(
shown actual size)
2.6 x 6mm
X
2
Plate
Big Washers
S
crew Used
(
shown actual size)
2.6 x 6mm Screws
with Washer
2
.6 x 6mm with washer
X2
Input Modular Jack
B
uzzer Pad
Remove
Backings
Modular Jack
P
C Board
Buzzer
S
crew Used
(
shown actual size)
2.6 x 6mm Screws
2
.6 x 6mm
X3
I
ndex Label Shield
I
ndex Label
Hook Switch
NO
TE:
Be
sure that the
Le
ver is abo
ve the
Hook Switch as
shown.
Lever
Decorative Piece
Push Button Panel
NOTE: Push
the Push Button
Panel up and
snap it into
position.
2.6 x 10mm Screws
Scre
ws Used
(sho
wn actual siz
e)
2
.6 x 10mm
X2
Handset Assembly
Speaker Pad
Remo
ve
B
acking
Speaker
Speaker Pad
Remove
Backing
Mute Button
Keypad Contact
Number
Button
Flash Button
Redial Button
3
21
6
54
9
87
#
0
*
Back View
Use this diagram as a
guide when installing
the number buttons.
NOTE: Make
sure that the angle
on the Flash, Redial,
and Mute b
uttons are
in the same
direction sho
wn.
K
e
ypad PC Boar
d
Rubber Microphone Cup
Microphone
Screw Used
(
shown actual size)
2
.6 x 6mm Screws
2.6 x 6mm Screws
2.6 x 6mm
X6
2
5
3
4
Modular Jack
Wiring/Tubing Assembly
NOTE: Follow
these steps for
wiring the speaker
wires to the PC
board wires.
1
Scre
w Used
(sho
wn actual siz
e)
2.6 x 14mm Screws
Cut
T
ubing
Slide
Tubing
onto wire
.
T
wist
wires
tog
ether
.
Slide
Tubing over
the twisted
wires.
2.6 x 14mm
X2
Wiring/Tubing Assembly
Coiled Cord
NOTE: When
snapping the receiver
co
ver on, start from the
back.
It may take a couple
attempts to attach
the two pieces.
Phone Number Shield
Phone Number
Label
2.6 x 14mm
Screws
Before the
Final
Assembly
Refer to Pages 5 & 6 and perform the
Transmit/Receive & Dial Tests.
Screw Used
(shown actual size)
2.6 x 14mm
X2
Final Assembly
Foam Feet
Bottom View
Remove
Backing
THIS UNIT COMPLIES WITH
PART 68 FCC RULES FCC NO.
GXA1CHN-74412-TE-E REN NO. 1.3B
USE STRANDARD JACK USOC RJ11C
FCC Label
Line Cord
Cop
yright © 2005 Elenco
®
Electr
onics,
Inc.
All Rights Reser
ved.
• 150 Carpenter A
ve
.
• Wheeling, IL 60090 • (800) 533-2441 Fax: (847) 520-0085 • e-mail: elenco@elenco.com • Website: www.elenco.com
You have now completed the assembly of the AK-750 Telephone Kit. Refer to HOW TO USE IT on
the other side. If the phone does not work, refer to TROUBLESHOOTING .
There are many other projects: RC Car, Talking Clock, etc. Ask your store about these
pr
ojects or call at (847) 541-3800.
2.6 x 6mm Screws
C
ontact Elenco
®
E
lectronics if you have any problems. Actual colors may vary from those shown here.
ASSEMBLY INSTRUCTIONS
Side View
Top View
Hook
Switch
Le
ver
Bend LED’s up
1
/8”
U
se scissors
to cut off 1/8”.
AK-750/FUN-755 AK-750/FUN-755
Long Part of Spring
Short Part of Spring
NO
TE:
Remo
ve an
y
burrs on the buttons
before installing them into
the Push Button Panel.
2
Remove Burrs
NOTE:
T
his
m
ay take a
couple attempts
to attach the two
pieces.
Remove
Screws Used
(sho
wn actual size)
3
x 7mm
X4
3 x 7mm Screws
Cut-away View
Hook Switch
Lever
To Next Page
Need help?
General