Elived YD1003-A - User Manual

To Next Page

Measure and note the width and the height

of the square or rectangle formed from the

VESA holes pattern .

Monitor PlateWall Plate Extenders

Nuts Bolts

x1x1

Step 2 Mesure your TV pattern

2M2M

100mm ≈ 4in.

130mm≈ 5 1/8in.

200mm ≈ 8in.

300mm ≈ 11 3/4in

340mm ≈ 13 3/4in.

400mm≈ 16in.

Select the configuration A , B , C, D, or E to use based on the measurement from STEP 2.

If your TV hole pattern is greater than 200x200mm, attach extenders [3A] and [3B] to monitor

plate [02] using Nut [4A] and Bolt [4B].

for VESA hole pattern:

300x300mm, 400x400mm

200 mm

400 mm

300 mm

for VESA hole

pattern:

200x300mm,

200x400mm

for VESA hole

pattern:

400x300mm,

for VESA hole pattern:

100x100mm, 130x130mm,200x100mm, 200x200mm.

200 mm

100 mm

130 mm

200 mm

100 mm

130 mm

VESA Pattern

(WxH)

Configuration

VESA Pattern

(WxH)

Configuration

100mm x 100mm A 300mm x 200mm C

130mm x 130mm A 300mm x 300mm E

200mm x 100mm A 400mm x 200mm C

200mm x 200mm A 400mm x 300mm D

200mm x 300mm B 400mm x 400mm E

200mm x 400mm B

M-A

Use the shorter screws

M-B

M-C

M-E

Not for M8 screws

M-FM-D

Step 3-3

Attach the brackets

(a) For Flat Back

(b) For Round Back / Extra Space

Hardware Included

Hardware (Wall /Product)

5/16 x 2½ in

Lag Bolts

Washers

Ø8mm

Open-end wrench

Max:400x400mm/16x16"

Min:75x75mm /3x3"

26"~55"

(V5.1)

YD1003-A

INSTALLATION INSTRUCTION

Philips Screws

M6 x 15mm

M6 x 30mm

Philips Screws

M4 x 12mm

M4 x 30mm

Washers

Ø6mm

M4-5-6

Spacers

L10mm

x4x4

Philips Screws

M8 x 25mm

M8 x 45mm

x4 x8 x4

Spacers

L5mm

TV Screws / Washers

M-A M-B M-C M-D M-E M-F

Step 1-1 Select TV screw diameter

Thread screws by hand into the threaded holes on the back of your TV to select which screw

diameter fits your TV.

M6M4

Correct

Too Long

Too Short

Step 1-2 Select TV screw length

for VESA hole pattern:

400x200mm, 300x200mm

02 4A 4B

M-A

Use the shorter screws

M-B

M-C

M-E

Not for M8 screws

Top of TV

Max:

(40KG)

88LBS

Safety Caution

Must Check Before Getting Started

Installation Tools (Not Included)

Band

Tape

Socket

Wrench

ScrewdriverPencil Electrodrill

Stud

Finder

HammerAwl

Wood

Drill Bit

Masonry

Drill Bit

Wood Stud Installation Concrete Installation

1/2"

(13mm)

3/8"

(10mm)

7/32"

(5.5mm)

Step 3-1 Select monitor plate configuration

Step 3-2

Assemble monitor plate and extenders

Bubble Level ×1

No!

When attaching brackets to the flat screen, be careful not to over tighten screws and

be sure that screws do not bottom out in the mounting holes.

MAX:400mm/16"

MAX:

400mm/16"

Min. 8"

(203mm)

Solid concrete wall

CAUTION: DO NOT install into drywall alone.

Max:

(40KG)

88LBS

Min. Wood Stud Size:

nominal 2”(51mm)

actual 1 1/2”(38mm)

Min. Wood Stud Size:

nominal 4”(102mm)

actual 3 1/2”(89mm)

<16mm(5/8")

Drywall with wood studs

If you have any questions, please contact us.

Please read this instruction carefully before installation.

If you do not understand these instructions or have doubts about the safety of the installation, assembly

or use of this product, please contact us.

● This product is designed for use in wood stud and solid concrete wall.

- DO NOT install into drywall alone.

● The wall must be capable of supporting five times the weight of the TV and mount combined.

● Do not apply this product to any purpose not indicated by ELIVED.

●

Incorrect installation may result in product damage or body inj

for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.

WARNING: This product contains small items that could be a choking hazard if swallowed.

Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage,

please contact us.

ury. ELIVED shall bear no responsibility

1 2

43 5

Need help?

Do you have a question about the Elived YD1003-A and is the answer not in the manual?

The ELIVED YD1003-A is a robust and versatile wall mount designed to securely hold flat-panel televisions ranging from 26 to 55 inches. This installation instruction manual provides comprehensive guidance for mounting the device on both wood stud and solid concrete walls, emphasizing safety and correct assembly procedures.

Function Description:

The primary function of the ELIVED YD1003-A is to provide a secure and adjustable mounting solution for televisions, allowing them to be positioned at an optimal viewing height and angle. The mount is designed to support TVs with VESA mounting patterns from 75x75mm (3x3 inches) up to 400x400mm (16x16 inches). It features tool-free tilting adjustment, enabling users to easily adjust the TV's vertical angle from -10° to +5° to reduce glare and achieve the best viewing experience. Additionally, it offers a leveling adjustment feature, allowing for a ±3° rotation to ensure the TV is perfectly horizontal after installation. The design incorporates a wall plate, monitor plates, and extenders to accommodate various TV sizes and VESA patterns.

Important Technical Specifications:

TV Size Compatibility: 26" to 55"
Weight Capacity: Maximum 88 LBS (40 KG)
VESA Compatibility:
- Minimum: 75x75mm (3x3 inches)
- Maximum: 400x400mm (16x16 inches)
Wall Type Compatibility: Wood stud walls and solid concrete walls. NOT suitable for drywall alone.
Tilting Angle: -10° to +5° (tool-free adjustment)
Leveling Adjustment: ±3°
Wall Plate Dimensions: 426.5mm (16.8") width, 200mm (7.9") height.
Monitor Plate Dimensions:
- Smallest configuration (A): 100mm x 100mm
- Largest configuration (E) with extenders: 400mm x 400mm
Distance from Wall (Minimum): Approximately 52mm (2")
Hardware Included:
- Wall Plate (01): 1 pc
- Monitor Plate (02): 1 pc
- Extenders (3A, 3B): 2 pcs each
- Lag Bolts (A): 3 pcs (5/16 x 2 1/2 in)
- Washers (B): 3 pcs (Ø8mm)
- Open-end wrench (C): 1 pc
- Nuts (4A): 8 pcs
- Bolts (4B): 8 pcs
- Bubble Level: 1 pc
- TV Screws (Philips Screws):
  - M4 x 12mm (M-A): 4 pcs
  - M6 x 15mm (M-B): 4 pcs
  - M8 x 25mm (M-C): 4 pcs
  - M4 x 30mm (M-D): 4 pcs
  - M6 x 30mm (M-E): 4 pcs
  - M8 x 45mm (M-F): 4 pcs
- Spacers:
  - Ø6mm L5mm (M-D): 8 pcs
  - Ø10mm L10mm (M-F): 8 pcs
- Washers (M4-5-6): 4 pcs (M-E)
Installation Tools (Not Included): Stud finder, awl, wood drill bit (7/32" or 5.5mm), masonry drill bit (3/8" or 10mm), hammer, tape, pencil, electrodrill, socket wrench, screwdriver.
Pilot Hole Depth (Wood Stud): 2 3/4 inches (70 mm)
Concrete Wall Anchor (NOT INCLUDED): Ø10*61mm (3 pcs recommended)

Usage Features:

Easy TV Screw Diameter Selection: Users are guided to thread screws by hand into the TV's threaded holes to determine the correct screw diameter (M4, M6, or M8) for their specific TV.
VESA Pattern Measurement: The manual instructs users to measure the width and height of the VESA hole pattern on their TV to select the appropriate monitor plate configuration (A, B, C, D, or E).
Extender Integration: For TVs with VESA patterns larger than 200x200mm, the included extenders (3A and 3B) can be easily attached to the monitor plate (02) using nuts (4A) and bolts (4B), expanding compatibility up to 400x400mm.
Flat Back and Round Back/Extra Space Mounting Options: The manual provides specific guidance for attaching brackets to TVs with either flat backs or those with round backs/extra space, recommending shorter screws for flat backs and longer screws with spacers for round backs or TVs with recessed mounting holes.
Wood Stud Installation: Detailed steps are provided for locating wood studs, marking pilot holes, and securely fastening the wall plate (01) using lag bolts (A) and washers (B). The importance of drilling pilot holes to the correct depth (70mm) into the center of the stud is highlighted.
Concrete/Brick Wall Installation: Instructions include marking pilot hole locations, drilling holes with a masonry drill bit, and installing the wall plate (01) using lag bolts (A), washers (B), and concrete anchors (not included).
Lift and Hang Mechanism: The design allows for easy lifting and hanging of the TV assembly (with attached brackets) onto the wall plate.
Tool-Free Tilting Adjustment: The TV's tilt angle can be adjusted between -10° and +5° without tools. If the TV tends to tilt downwards, users can pull the TV to the desired angle and then fasten the tilting nuts with an open-end wrench.
Leveling Adjustment: A ±3° leveling adjustment is available by adjusting two screws with an open-end wrench, ensuring the TV is perfectly horizontal.
Safety Precautions: The manual emphasizes critical safety warnings, such as not installing into drywall alone, ensuring the wall can support five times the combined weight of the TV and mount, and verifying all parts are included and undamaged before assembly. It also warns against overtightening screws and ensuring they do not bottom out in the mounting holes.

Maintenance Features:

Durability: The mount is constructed to support up to 88 LBS (40 KG), indicating a robust design intended for long-term use.
Adjustability for Longevity: The tilting and leveling adjustments allow for fine-tuning over time, accommodating minor shifts or preferences without needing to remount the entire system.
Clear Installation Instructions: The detailed, step-by-step instructions, accompanied by illustrations, facilitate correct initial installation, which is crucial for the mount's stability and longevity.
Contact for Support: The manual encourages users to contact ELIVED if they have questions or doubts about safety, installation, assembly, or use, ensuring ongoing support for product maintenance and troubleshooting.
Part Replacement: The mention of contacting ELIVED for additional concrete wall anchors suggests that replacement or additional parts may be available, contributing to the long-term usability of the mount.

The ELIVED YD1003-A is a comprehensive mounting solution that prioritizes safety, ease of installation, and user-friendly adjustments, making it a reliable choice for mounting compatible televisions.

Elived YD1003-A Specifications

General

Brand	Elived
Model	YD1003-A
Category	TV Mount
Language	English

Related product manuals