Ellesse PERFORMANCE Series User Manual

(D) SWITCHING BETWEEN T1 AND T2
(B) MAIN COMPONENTS
S1
S2
S4
S3
Crown
Hour
Minute
Second
Hold S3 for about 4 sec to T1/T2
(A) SPECIFICATION
1. Type: Ana-digi Quartz Watch
2. Additional functions:
Digital hour, Minute, Second (6 digit), Day, Year, Month, Date
Chronograph
Alarm
Timer
Dual Time
3. Power cell no.: CR2025 or Equivalent
4. Water Resistant: 100M
(C) ANALOGUE TIME SETTING
Pull out the crown when the second hand at the 12 O'clock position.
Turn the crown clockwise or anti-clockwise to the desired time.
Push the crown back.
Hold S1 for about 5 sec to set Push S3/S4 to reset sec. '00' Push S3/S4 to adjust hour
Push S3/S4 to adjust minute Push S3/S4 to adjust year Push S3/S4 to adjust month
(E) DIGITAL TIME AND CALENDAR SETTING
ELI 614
S1
S2
S4
S3
S1
S2
S4
S3
Push S2
to Minute
Setting
Push S2
to Year
Setting
Push S2
to Month
Setting
S1
S2
S4
S3
S1
S2
S4
S3
S1
S2
S4
S3
Push S2
To Hour
Setting
S1
S2
S4
S3
S1
S2
S4
S3
Hold S3 To T1/T2
S1
S2
S4
S3
PERFORMANCE SERIES
P-400 AN
ED008U
IMPORTANT
• Push buttons are not to be operated under water.
• This watch contains electronic components. Never attempt to open
the case or remove the back cover.
• Should water or condensation appear in the watch, have the watch
checked immediately, corrosion of electronic parts can occur inside
the case.
• Avoid exposing the watch to extreme temperature.
• Avoid severe impact. The watch is designed to withstand impact
under normal use. It is inadvisable to subject it to severe impact or
rough usage.
• Clean the watch with soft cloth and clean water only. Avoid using
chemicals - especially soap as the waterproof gasket will corrode.
• Keep watch away from the conditions of strong electric field and static
electricity.
• Replace battery by authorized service centre. Otherwise, the water
resistance function may be affected.
• For watches fitted with resin straps. You may notice a whitish powdery
substance on the band. This substance will not harm your skin or
clothing, and can be removed by simply wiping it with a cloth.
• For watches with light colour and transparent straps, there may be
colour change on the strap after wear for some time.
• Do not return crown to normal position while chronograph second
hand returns to 12:00 (ZERO) position.
• Hand stops on the way when crown are returned to normal position
and these positions are recognized as 12:00 (ZERO) position.
• Before resetting the time, make sure the chronograph is not in function
and the chronograph hands are precisely at zero.
• Calendar position may vary, depending on design. But the functions
and setting are the same.

Ellesse PERFORMANCE Series Specifications

General

Movement	Quartz
Water Resistance	50 meters
Case Material	Stainless steel
Band Material	Silicone
Display Type	Analog
Features	Chronograph, Date Display

Summary

Important Operating Instructions and Warnings

Button Operation and Water Resistance

Do not operate buttons under water; check for water ingress to prevent corrosion.

Electronic Component Care

Keep away from strong electric fields and static electricity; do not open the case.

Chronograph and Time Setting Precautions

Set chronograph to zero before time setting; ensure hands are at zero position.

Temperature and Impact Avoidance

Avoid extreme temperatures and severe impacts to protect the watch.

Cleaning and Maintenance

Clean with soft cloth and water only; avoid chemicals. Replace battery at authorized center.

Strap Care

Resin straps may develop powdery substance; light straps may discolor over time.

Watch Specifications

Watch Type and Functions

Ana-digi Quartz Watch with digital time, date, chronograph, alarm, timer, and dual time.

Power Cell and Water Resistance

Uses CR2025 battery and is water resistant to 100M.

Setting Analogue Time

Crown Operation for Analogue Time

Pull crown to set time by turning clockwise/anti-clockwise, then push back.

Switching Between Time Zones T1 and T2

T1/T2 Time Zone Switching

Hold S3 for approximately 4 seconds to switch between Time 1 and Time 2.

Setting Digital Time and Calendar

Digital Time Setting

Use S1 to enter setting mode, S2 to cycle through fields, S3/S4 to adjust values.

Second Hand Reset

Push S3/S4 to reset the second hand to '00'.

Calendar Setting

Access date, month, year, and day settings via S2, adjust with S3/S4.

Date and Day Setting

Use S2 to select date, month, year, and day settings; adjust with S3/S4.

12/24 Hour Format

Press S2 to cycle to 12/24H setting and adjust using S3/S4.

Month-Day/Day-Month Format

Press S2 to select M-D or D-M format and adjust with S3/S4.

Time Setting Completion

Press S1 to exit setting mode after all adjustments are made.

Chronograph Mode Operations

Entering Chronograph Mode

Press S2 to enter Chronograph Mode.

Chronograph Start and Stop

Use S4 to start/stop the chronograph; use S3 to record laps.

Split Lap and Recall

Use S3 to split lap times and S1 to recall split lap records.

Chronograph Reset

Press S1 to reset the chronograph.

Free Lap and Countdown

Hold S3 for 3 seconds for free laps; use S4 to start countdown timer.

Timer Mode Operations

Entering Timer Mode

Press S2 to enter Timer Mode.

Timer Setting

Use S2 to select hour, minute, or second setting; adjust with S3/S4.

Timer Start and Stop

Use S4 to start the timer; hold S1 to set timer.

Alarm Mode Operations

Entering Alarm Mode

Press S2 to enter Alarm Mode.

Alarm Setting

Use S2 to set alarm time (hour/minute); adjust with S3/S4.

Alarm and Chime Control

Use S4 to turn alarm on/off; use S3 to control chime or Alarm 2.

Setting Alarm 2

Press S3 to access and set Alarm 2.