Elma Elmasonic S100 - User Manual

Questions and Answers

L
Leah PowersAug 16, 2025
Why are my Elma Elmasonic S100 Ultrasonic Jewelry Cleaner results unsatisfactory?
- J
  Jennifer ArroyoAug 16, 2025
  Unsatisfactory cleaning results with your Elma Ultrasonic Jewelry Cleaner may occur if you are not using a suitable cleaning medium, or if you are not using any cleaning medium at all. In this case, use a suitable cleaning medium. Also, the cleaning temperature might not be sufficient, so heat up the cleaning liquid. Finally, the cleaning period may be too short, so repeat the cleaning interval.
S
Sarah McconnellAug 19, 2025
What to do if the Elma Elmasonic S100 Ultrasonic Jewelry Cleaner has no ultrasonic function and the LED is dark?
- S
  seth89Sep 12, 2025
  If your Elma Ultrasonic Jewelry Cleaner has no ultrasonic function and the LED ultrasound is dark, first ensure that the turning knob for ultrasonic operation is not in the '0' position; if it is, switch it on. Check that the unit is switched on at the key on/off. Also, verify that the ultrasound key is pressed. If the issue persists, it may indicate a fault of electronics, in which case you should return the unit to the supplier or manufacturer.
J
Jacqueline FieldsAug 21, 2025
How to fix Elma Elmasonic S100 with no operating functions and all LEDs dark?
- L
  liuyvetteAug 21, 2025
  If your Elma Ultrasonic Jewelry Cleaner has no operating functions and all LEDs are dark, first ensure that the mains cable is plugged in. If it is, check the socket and fuse to ensure they are functional. If the problem persists, the mains cable may be damaged or interrupted, requiring replacement. In the case of a fault of electronics, return the unit to the supplier or manufacturer.
T
Troy HollowayAug 25, 2025
What to do if my Elma Elmasonic S100 unit does not heat up and the LED temperature is dark?
- S
  Sheri PetersAug 26, 2025
  If your Elma Ultrasonic Jewelry Cleaner does not heat up and the LED temperature is dark, check that the turning knob temperature is not in the '0' position; if it is, switch it on. Also, verify that the unit is switched on with the key on/off. If the issue persists, it may indicate a fault of electronics, and you should return the unit to the supplier or manufacturer.
H
hernandezseanAug 28, 2025
What causes the set temperature to be exceeded in my Elma Elmasonic S100?
- C
  charles78Aug 28, 2025
  The set temperature in your Elma Ultrasonic Jewelry Cleaner might be exceeded because the temperature sensor does not measure the average temperature due to lack of revolution, so mix the liquid manually or by means of ultrasound. Also, if the set temperature is too low, the ultrasonic energy heats up the liquid more than required, so for low set temperatures, do not switch on heating. Also, switch on ultrasound for short periods only.
K
kyle13Aug 31, 2025
Why is the heating-up period unsatisfactory for my Elma Elmasonic S100 Ultrasonic Jewelry Cleaner?
- C
  Cindy BeckerAug 31, 2025
  An unsatisfactory heating-up period in your Elma Ultrasonic Jewelry Cleaner could be due to loss of heating energy; use a cover (optional accessory equipment). It could also be caused by no mixing of cleaning liquid, so switch on ultrasound.
M
maureen96Sep 2, 2025
Why does my Elma Ultrasonic Jewelry Cleaner produce a boiling noise during heating-up?
- W
  weissdavidSep 3, 2025
  If your Elma Ultrasonic Jewelry Cleaner produces a boiling noise during heating-up, it may be due to no mixing of cleaning liquid, so switch on ultrasound.
R
Richard BurnettSep 5, 2025
What to do if the casing of my Elma Elmasonic S100 is damaged?
- H
  hunterjustinSep 6, 2025
  If the casing of your Elma Ultrasonic Jewelry Cleaner is damaged due to damage by a third party or transport damage, return the unit to the supplier or manufacturer.
D
Derek NealSep 9, 2025
What does it mean if the LEDs of LED temperature blink alternately on my Elma Elmasonic S100 Ultrasonic Jewelry Cleaner?
- B
  Brian EllisSep 9, 2025
  If the LEDs of LED temperature blink alternately on your Elma Ultrasonic Jewelry Cleaner, this indicates a heating fault. Turn the unit off and on. If the fault indication persists, return the unit to the supplier or manufacturer.
D
Danielle JacksonSep 12, 2025
What does it mean if the LEDs of LED ultrasound and LED temperature blink alternately on my Elma Elmasonic S100 Ultrasonic Jewelry Cleaner?
- M
  Meghan JacksonSep 12, 2025
  If the LEDs of LED ultrasound and LED temperature blink alternately on your Elma Ultrasonic Jewelry Cleaner, this indicates a fault in the programme control. Turn the unit off and on. If the fault indication persists, return the unit to the supplier or manufacturer.

Summary

Important Safety Warnings

Unit Usage Guidelines

The Elma ultrasonic unit is designed for treating items and liquids only, not living beings.

Safety Precautions and Risk Avoidance

Covers electrical safety, cleaning liquid, hot surfaces, noise, liability, and splashing risks.

Medical Device Intended Use & Machine Safety

Defines intended use for medical devices and safety instructions visible on the machine.

Functioning Principles

Ultrasonic Cleaning Factors Explained

Product Description and Features

Operating Elements (S 15 - S 900 H)

Detailed description of controls and indicators for S 15 to S 900 H models.

Operating Elements (S 10; S 10 H)

Specific controls and indicators for S 10 and S 10 H models.

Operation and Display Function Summary

Initial Operation and Setup

Preparation and Placement Guidelines

Mains Connection Requirements

Specifies required mains voltage, connection procedures, and safety precautions.

Putting Unit into Operation

Filling the Unit Tank

Degassing the Cleaning Liquid

Ultrasonic Cleaning Process

Heating the Cleaning Liquid

Instructions for heating the cleaning liquid, including temperature recommendations and safety.

Temperature-Controlled Cleaning

How to start the cleaning process automatically when the set temperature is reached.

Automatic Liquid Mixing During Heating

Manual Cleaning Process Start

Steps for manually starting the ultrasonic cleaning process, including period selection and operation modes.

Cleaning Media Guidelines

Solvents and Flammable Cleaner Limitations

Aqueous and Chemical Cleaner Limitations

Maintenance and Care

Repair and Authorized Personnel

Troubleshooting Guide

Elma Elmasonic S100 Specifications

General

Ultrasonic Frequency	37 kHz
Material Tank	Stainless steel
Material Housing	Stainless steel
Heating	Yes
Timer	1-30 min and continuous operation
Material	Stainless steel
Tank Capacity	9.5 liters