To Next PageTo Next Page
Need help?Do you have a question about the EMC-PARTNER MIG-OS-OS1 and is the answer not in the manual?
General| Brand | EMC-PARTNER |
|---|---|
| Model | MIG-OS-OS1 |
| Category | Pulse Generator |
| Language | English |
Overview of the MIG-OS-OS1 tester.
Overview of the MIG0603OSI tester.
Important operational notes and warnings.
States conformity to product standards and directives.
Details the function and application of the damped oscillatory wave tester.
Explains the Combination Wave Generator (CWG) and its applications.
Describes voltage tests using 1.2/50 µs waveform and 0.5 J energy.
Overview of combined and special MIG testers.
Overview of the MIG generator's capabilities and models.
Explains MIG tester use for capacitor tests and CWG.
Technical specifications for 1 MHz and 100 kHz damped oscillatory waves.
Technical data for the Combination Wave Generator (1.2/50 µs; 8/20 µs).
Technical data for voltage tests with 1.2/50 µs, 0.5 J, and 500 Ω.
General control information for MIG testers.
Details the auxiliary port and its pin assignments.
Mechanical dimensions for MIGxxxxOSx testers and accessories.
Information on power supply requirements and connections.
Lists included articles and their dimensions for MIG testers.
Lists standard accessories for MIG testers.
Outlines the safety standards the MIG0603-Oxx complies with.
Specifies the operating temperature, humidity, and pressure requirements.
Provides essential safety rules for using the high-voltage generators.
Details EMC immunity requirements and potential disturbances.
States the manual's importance for safety and operation.
Provides a general overview of the MIG generator's flexible kit system.
Describes the high voltage modules forming the basis of MIG generators.
Explains the measuring circuits used for CWG functions.
Details the important elements on the front panel of the MIG0603-Oxx.
Explains the microprocessor-controlled aspects of the MIG0603-Oxx control panel.
Describes the functions of various buttons on the front panel.
Details controls on the operation panel, including start, stop, and safety circuits.
Details the rear panel layout and connectors of the MIG0603-Oxx.
Describes rear panel ports for power, communication, and accessories.
Explains inputs for EUT failure detection and external triggering.
Emphasizes manual importance and specifies operator qualifications.
Outlines pre-operation checks for the tester.
Details power source checks and connection procedures.
Guides on setting up tests for 1.2/50 µs and 8/20 µs combination wave pulses.
Details considerations for setting up damped oscillatory wave tests.
Provides guidance for setting up 0.5 J and 500 Ω tests.
Guides on performing quick start tests with the MIG0603-Oxx.
Explains how to change the tester's display language.
Details options for printer output and beeper settings.
Describes how to perform damped oscillatory wave tests.
Explains how to perform combination wave tests.
Guides on performing tests with the 0.5J, 500 Ohm setting.
Overview of programmable tests for damped oscillatory testers.
Details how to set nominal values in the "Main" menu.
Setting nominal values for 1 MHz Damped Oscillatory Wave tests.
Setting nominal values for 100 kHz Damped Oscillatory Wave tests.
Editing parameters for 0.5 J, 500 Ω tests.
Editing parameters for Combination Wave Tests.
Describes voltage ramp functions for SURGE and 1.2/50 0.5 J tests.
Details ramp functions for polarity changes.
Explains synchronisation ramp functions with external CDN.
Describes how EUT errors are controlled and initiated.
Guides on starting, stopping, and standby modes for high voltage tests.
Explains the purpose and function of the safety circuit.
Provides connection details for EUT for various test types.
Instructions for routine maintenance, including cleaning the air filter.
Procedures for user verification of high voltage pulse generation.
Verification steps for the Combination Wave Tester.
Verification steps for the Damped Oscillatory Wave tester.
Information on verification performed by EMC PARTNER before delivery.
Lists and explains error messages related to incorrect inputs.
Lists and explains failure messages indicating generator malfunction.
Describes attention notices for generator stop conditions.
Information on service and repair procedures.
States that no spare parts are necessary.
Contact details for the EMC PARTNER service department.
Instructions for taking the MIG0603-Oxx out of operation.
States that dismantling the MIG0603-Oxx is safe and lists recyclable parts.
Instructions for packaging the MIG0603-Oxx for transport.
Recommendations for transporting the MIG0603-Oxx, including for outdoor tests.
Lists accessories for the MIGxxxOxx system.
Lists accessories for MIG-OS-OS and MIG0603OSI testers.
Introduces the remote control option via RS-232 serial port.
Details the technical specifications of the RS 232C serial port.
Explains the structure of remote control commands.
Defines the syntax rules for remote control commands.
Outlines the structure of setup commands.
Explains how to inquire for generator data.
Lists and explains failure messages encountered during remote control.
Lists and explains various remote control commands.
Instructions for setting up the GENECS software.
Describes the GENECS software interface.
Explains the GENECS library for test specifications.
Details protocol options within GENECS for test reports.
Explains the function of the GENECS log file.
Describes GENECS software preferences for editors and display.
Defines waveform combinations and specific waveforms.
Information regarding corrections and conformity declarations.
