EMC VNX VG8 User Manual

318 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Page #146 background image

Loading...

Page #146 background image

EMC CONFIDENTIAL

Table of Contents

Default Chapter3
- Table of Contents3
Phase 1 Installation17
Chapter 1 Introduction19
- Product Introduction20
- Setup Process Overview21
- How Setup Works24
- Additional Information31
Chapter 2 Before Installing33
- Step 1: Check Components34
- VG2/VG8 CPU and Power Supply/ Cooling Modules39
- Identifying Blades and I/O Modules40
- Direct- or Fabric-Connected45
- Step 2: Confirm Site Preparation47
- Step 3: Collect Configuration Information50
Part 2 Phase 2 Installation51
Chapter 3 Install Components in Customer's Cabinet53
- Installing Components54
- Component Layout55
- System Cabling56
Chapter 4 Connect Cables for a Fabric-Connected VG257
- Step 1: Blade Fibre Channel Cables58
- Step 2: Array Fibre Channel Cables60
- Step 3: Serial Cables72
- Step 4: Optional Tape Backup Device Cables73
- Step 5: Private LAN Cables74
- Step 6: External Network Cables76
Chapter 5 Connect Cables for a Direct-Connected VG280
- Step 1: Blade Fibre Channel Cables80
  - Connecting a VNX5300 or VNX5500 Array81
  - Connecting a VNX5700 or VNX7500 Array82
- Step 2: Serial Cables83
- Step 3: Optional Tape Backup Device Cables84
- Step 4: Private LAN Cables85
- Step 5: External Network Cables87
Chapter 6 Connect Cables for a Fabric-Connected VG890
- Step 1: Blade Fibre Channel Cables90
- Step 2: Array Fibre Channel Cables93
Chapter 7 Connect Cables for a Direct-Connected VG8113
- Step 1: Blade Fibre Channel Cables114
  - Connecting a VNX5300 or VNX5500 Array115
  - Connecting a VNX5700 or VNX7500 Array116
- Step 2: Serial Cables118
- Step 3: Optional Tape Backup Device Cables119
- Step 4: Private LAN Cables120
- Step 5: External Network Cables123
Chapter 8 Configure the Boot Array125
- Step 1: Verify Power Cables Are Disconnected126
- Step 2: Power up the Boot Array126
- Step 3: Verify VNX Array Software Versions127
  - Using Unisphere128
  - Using Navisphere CLI129
- Step 4: Verify VNX Array Read and Write Cache Settings130
  - Using Unisphere131
  - Using Navisphere CLI132
- Step 5: Verify Domain Security Is Configured132
  - Using Unisphere133
  - Using Naviseccli133
Chapter 9 Install and Configure EMC NAS Software136
- Step 1: Power up the VNX Gateway System136
  - Power up the VNX Cabinet136
- Step 2: Install Latest File OE on CS 0139
- Step 3: Install Latest File OE on CS 1141
  - Procedure141
- Step 4: Configure Connecthome142
- Step 5: Check System Status143
- Step 6: Enable Licensed Features143
- Step 7: Complete the Hand-Off Worksheet144
- Step 8: Final Configuration144
Phase 3 Installation145
Chapter 10 Complete Phase 3 Installation147
- Introduction148
  - Phase 3: Preparation Checklist148
- Phase 3 Setup Tasks149
- Add Additional Arrays150
  - Adding an Array150
  - Adding a Symmetrix Array154
- Create User Luns155
- Prepare for Customer Data157
Appendixes163
Appendix A Change Connecthome Dialing Configuration165
- When to Change the Connecthome Dialing Configuration166
- Disabling Dial Tone Detection167
- Setting the Country Code on the MT5634ZBA Modem168
  - Windows-Based PC Instructions168
  - Manual Instructions for Setting the Country Code170
Appendix B Change IP Addresses173
- Change Private IP Addresses174
- Change Primary Subnet176
- Change Secondary Subnet180
Appendix C Backend Storage Requirements Check Failed Error186
- Introduction186
  - Backend Storage Requirements Check Failed186
  - This Appendix Describes How to Correct the Following Error by Upgrading the Software186
- Upgrade the Operating Environment187
- Commit the Operating Environment193
  - Sample Error Message193
  - Remedy193
- Enable Read and Write Cache194
Appendix D Resolve Blade Boot Failures197
- Manually Set the Blade Fibre Speed198
- Verify Fibre Channel Port Link Lights199
Appendix Enas Install Options202
- Express Install for File OE Release 7.0 or Lower202
- Express Install for File OE Release 7.1 or Higher217
- Using the Kickstart Installation Option (File OE Release 7.0 or Lower)228
- If the Software Installation Fails229
  - For a VNX Boot Array229
  - For a Symmetrix Boot Array229
Manually Zone Switches and Configure System Luns231
Appendix F Manually Zone Switches and Configure System Luns232
- Zone the Fc/Fcoe Switches by WWN232
- Create Control Luns on VNX Array237
Cable Connections from Fibre Channel Switch to Storage Array251
Appendix G Cable Connections from Fibre Channel Switch to Storage Array252
- Connecting a Clariion CX300 or CX500 Array252
- Connecting a Clariion CX700 Array254
- Connecting a Clariion CX3-10 Array256
- Connecting a Clariion CX3-20 or CX3-40 Array258
- Connecting a Clariion CX3-80 Array260
- Connecting a Clariion CX4-960 Array262
- Connecting a Clariion CX4-480 Array264
- Connecting a Clariion CX4-240 Array266
- Connecting a Clariion CX4-120 Array268
Setup Worksheets271
Appendix H Setup Worksheets272
- Site Preparation Worksheet272
- Fc/Fcoe Cabling Worksheet273
- VNX Boot Array Worksheet276
- Control Station 0 Networking Worksheet277
- Control Station 1 Networking Worksheet278
- Private LAN Worksheet280
- Phase 2 Completion Hand-Off Worksheet282
- Setup Celerra Wizard Worksheets283
- Iscsi Wizard Worksheets296
  - Create an Iscsi Target Worksheet296
  - Create an Iscsi LUN Worksheet296
- Connecthome Configuration Worksheet298
Navisphere Manager Procedures301
Appendix I Navisphere Manager Procedures302
- Collecting Backend Wwns302
- Creating Control Luns on Clariion Array303
- Verifying Clariion Array Software Versions310
- Verifying Clariion Array Read and Write Cache Settings311
- Verifying Navisphere Domain Security Is Configured313

Questions and Answers:

Need help?

Do you have a question about the EMC VNX VG8 and is the answer not in the manual?

EMC VNX VG8 Specifications

General

Brand	EMC
Model	VNX VG8
Category	Gateway
Language	English

Related product manuals

Preview: EMC VNX VG2