To Next PageTo Next Page
Need help?Do you have a question about the EMKO EZM-4430 and is the answer not in the manual?
General| Brand | EMKO |
|---|---|
| Model | EZM-4430 |
| Category | Cash Counter |
| Language | English |
Details the technical specifications and features of the EZM-4430 counter.
Provides details on how to order the EZM-4430 counter with various configurations.
Outlines the warranty period and conditions for the EMKO EZM-4430 counter.
Offers guidelines for cleaning and basic upkeep of the EZM-4430 programmable counter.
Provides an overview of the EZM-4430 counter's front panel, device label, and mounting clamps.
Details the physical dimensions and panel cut-out requirements for the EZM-4430 counter.
Specifies the required dimensions for the panel opening to mount the EZM-4430 counter.
Lists the operating conditions, forbidden conditions, and altitude limits for the EZM-4430 counter.
Explains the step-by-step procedure for mounting the EZM-4430 counter onto a control panel.
Details how to use the fixing clamps for secure panel mounting of the EZM-4430 counter.
Provides instructions on how to safely remove the EZM-4430 counter from its panel mount.
Illustrates the terminal layout and provides instructions for making electrical connections to the EZM-4430.
Presents the detailed wiring diagram for connecting sensors, inputs, outputs, and power to the EZM-4430.
Shows the labeling on the EZM-4430 device, indicating terminal functions and specifications.
Explains how to connect the power supply voltage to the EZM-4430 counter, including fuse and switch requirements.
Details how to connect various counting inputs like proximity sensors and switches to the EZM-4430.
Illustrates wiring for NPN and PNP proximity sensors and simple switches for counting inputs.
Shows how to connect incremental encoders and switches for counting inputs to the EZM-4430.
Provides wiring diagrams for connecting simple switches to the counting inputs of the EZM-4430.
Illustrates the wiring diagram for the relay output of the EZM-4430 counter.
Presents the galvanic isolation test results for the EZM-4430 programmable counter.
Details the functions of the buttons, displays, and LED indicators on the EZM-4430's front panel.
Describes what is displayed on the EZM-4430 screen when power is applied, including software revision.
Provides a step-by-step guide on how to change and save the Set Value (SV) on the EZM-4430 counter.
Explains how to reset the count value using the RESET button or input, and the effect on actual and SET values.
Details the process of accessing and navigating through the EZM-4430's program parameters, including password entry.
Defines the various input types and functional behaviors available for the EZM-4430 counter.
Explains x1 phase shifting for incremental encoders, defining counting based on Ch-A and Ch-B signals.
Details x2 phase shifting for incremental encoders, covering various counting scenarios with Ch-A and Ch-B.
Describes x4 phase shifting for incremental encoders, outlining complex counting logic with Ch-A and Ch-B.
Sets protective pulse time for Ch-A and Ch-B inputs against debounce and weak signals.
Sets protective pulse time for reset and pause inputs against debounce and weak signals.
Configures the counting direction (upcount or downcount) for the EZM-4430 counter.
Selects the sensor type (NPN or PNP) for the counting inputs of the EZM-4430.
Defines 'Manual Reset-1' output behavior, where counting continues until manual reset.
Defines 'Manual Reset-2' output behavior, where counting stops at SET value until manual reset.
Details 'Manual Reset-3' output behavior, considering output pulse time for state changes.
Explains 'Automatic Reset-1' behavior, where count resets automatically after reaching SET value.
Details 'Automatic Reset-2' behavior, including reset and counting start points based on pulse time.
Describes 'Automatic Reset-3' behavior, where output changes at SET value, with specific conditions for pulse time.
Explains 'Automatic Reset-4' behavior, where output changes at SET value and counting resets.
Details 'Automatic Reset-5' behavior, where output state depends on count value relative to SET value.
Describes 'Automatic Reset-6' behavior, with output changes at 0 value and conditions for count value.
Explains 'Automatic Reset-7' behavior, where output state depends on count value relative to SET value or zero.
Configures whether the output is normally non-energized or energized during operation.
Sets the duration for which the output signal remains active after a counting event.
Specifies the decimal point position for the display of values on the EZM-4430 counter.
Defines how count values are saved to memory upon power disconnection and restoration.
Configures protection levels for the reset function and the ability to change the set value.
Sets a multiplier to scale the counted pulses, affecting the displayed value.
Determines the value to which the counter resets after a reset operation.
Sets or changes the password required to access the program parameters of the counter.
