EMKO EZM-4430 Manual

EZM-4430,EZM-4930,EZM-7730,EZM-9930
ProgrammableCounters
-6digitsProcess(PV)and6digitsSet(SV)ValueDisplay
- Operation with 1 Set Value
- Reset , Pause and ChA-ChB Counting Inputs
- NPN/PNP Type Operation
- Operation with Automatic and Manual Reset
- INC,DEC,INC/INC,INC/DEC,UP/DOWN, x1 / x2 / x4 Counting
with Phase Shifting Property
- Multiplication Coefficient and Decimal Point Position
EZM-4430,EZM-4930,EZM-7730,EZM-9930
ProgrammableCounters
ElectricalWirings
IntroductionBrochure.ENG EZM-XX3001V0403/17
SPECIFICATIONS:
INPUTS:
Output:Process RelayOutput(5A@250V atResistiveLoad)V
CountingInputs(Ch-A,Ch-B):
ResetInput:
PauseInput:
SensorTypeSelection:
ResetFunction:
CountInputTypesandMaximumFrequency:
ResetandPauseInputFilter:2-50msec
OUTPUT
Switch,Proximity,Capacitive
sensororencodercanbeconnected.
Switch,Proximity,Capacitivesensororencodercan
beconnected.
Switch,Proximity,Capacitivesensororencodercan
beconnected.
NPNorPNP canbeselected.
AutomaticorManual.
INC,DEC,INC/INC,INC/DEC,UP/DOWNmax.20kHZ.
x1/x2/x4:PhaseShift(forencoder)Counting;Max.10kHZ.
(Canbeadjustedin
parameter.)
DISPLAY :
Process Value Display :
Set Value Display :
LED Display :
EZM-4430 : 8 mm Red 6 digit LED Display
EZM-4930 : 13.2 mm Red 6 digit LED Display
EZM-7730 : 10.8 mm Red 6 digit LED Display
EZM-9930 : 13.2 mm Red 6 digit LED Display
EZM-4430 : 8 mm Green 6 digit LED Display
EZM-4930 : 8 mm Green 6 digit LED Display
EZM-7730 : 8 mm Green 6 digit LED Display
EZM-9930 : 8 mm Green 6 digit LED Display
SV(Set value),OP(Output Position) LEDs.
ENVIRONMENTAL RATINGSandPHYSICAL SPECIFICATIONS
OperatingTemperature
Humidity
ProtectionClass
Weight
Dimensions
Panel Cut-Out:
nonecondensing),
atfront, atrear.
Depth
Depth
Depth
Depth
:
:
:
:
:
0...50°C
0-90%RH(
Ip65 Ip20
EZM-4430 : 10 gr.
EZM-4930 : 40 gr.
EZM-7730: 0gr.
EZM-9930: 0gr.
EZM-4430 : (48 x 48mm, :95 mm)
EZM-4930 : (96 x 48mm, :96 mm)
EZM-7730 : (72 x72mm, :95.5 mm)
EZM-9930 : (96 x 96mm, :96 mm)
EZM-4430 : (48 x 48mm)
EZM-4930 : (96 x 48mm)
EZM-7730 : (72 x72mm)
EZM-9930 : (96 x 96mm)
2
2
27
34
SUPPLY VOLTAGE
230V 50/60Hz(-15%;+10%)2.3VA
115V (-15%;+10%)-2.3VA
24V 50/60Hz(-15%;+10%)2.3VA
(Mustbedeterminedinorder.)
V
V
V
24V (-%15;+%15)/24V 50/60Hz(-%15;+%15)Z V 4VA
DIMENSIONS
PANEL MOUNTING
1-
2-
3-
Before mounting the device
in your panel, make sure that
the panel cut-out is suitable.
Check front panel gasket
Position.
Insert the device through
the cut-out. If the mounting
clamp are on the unit, put out
them before inserting the unit
to the panel.
4- Insert the unit in the panel
cut-out from the front side.
5- Insert the mounting clamps
to the holes that located top
and bottom sides of device
and screw up the fixing screws
until the unit completely
immobile within the panel.
PanelCut-out
Sensor
Supply
RelayOutput
SupplySwitch
Fuse
Sensor
Supply
RelayOutput
SupplySwitch
Fuse
Sensor
Supply
RelayOutput
SupplySwitch
Fuse
Sensor
Supply
RelayOutput
SupplySwitch
Fuse
4
5
96mm/3.78inch
48mm/1.89inch
72mm/2.83inch
72mm/2.83inch
11.5 mm/0.45inch±1
84mm/3.31inch
11.5 mm/0.45inch±1
84mm/3.31inch
Maximum15mm/0.59inch
Maximum15mm/0.59inch
Maximum15mm/0.59inch
10.5 mm/0.41inch±1 76mm/2.99inch
96mm/3.78inch
SV
SV
OP
OP
Counter
EZM-4930
SET
P
RESET
Maximum15mm/0.59inch
11.5 mm/0.45inch±1
84mm/3.31inch
48mm/1.89inch
48mm/1.89inch
96mm/3.78inch
EZM-4430
EZM-4930
EZM-7730
EZM-9930
65mm/2.56inch(min)
46mm/1.81inch(min)
46mm/1.81inch(min)
65mm/2.56inch(min)
129mm/5.08inch(min)
46mm/1.81inch(min)
65mm/2.56inch(min)
97mm/3.82inch(min)
69mm/2.72inch(min)
69mm/2.72inch(min)
97mm/3.82inch(min)
129mm/5.08inch(min)
92mm/3.62inch(min)
129mm/5.08inch(min)
92mm/3.62inch(min)
92mm/3.62inch(min)

EMKO EZM-4430 Specifications

General

Brand	EMKO
Model	EZM-4430
Category	Cash Counter
Language	English