Emos E0211 User Manual

4
reception of the DCF signal, the icon will be displayed permanently. If the clock has not been automatically set and the
icon is not displayed within 10 minutes, the receiver is likely badly placed (most common cause). Test reception in various places.
Do not place the clock on metal objects. Do not place the clock in the proximity of electrical appliances, such as TVs, computers,
monitors, microwave ovens etc. Interfering electrical elds from these appliances can reach up to 2 metres. DCF signal reception
can be activated manually by long pressing the DOWN button. Deactivate searching for signal by short pressing the DOWN button.
The radio controlled clock provides the most accurate time on the European continent. The radio signal propagates via radio
waves (77.5 kHz) from a site near Frankfurt on the Main in Germany within a range of 1 500 km. This radio time signal automat-
ically takes into account summer (DST) and winter time, leap years and date changes. In standard conditions (at safe distance
from sources of interference, such as TV sets, computer monitors), the reception of time signal takes several minutes. If the clock
does not detect the signal, follow these steps:
1. Move the weather station to another location and try to detect the DCF signal again.
2. Make sure the distance of the clock from sources of interference, such as computer monitors or television sets, is at least
1.5 to 2 meters when receiving this signal. When receiving DCF signal, do not put the weather station in the proximity of
metal doors, window frames and other metal structures or objects (washing machines, dryers, refrigerators etc.).
3. In reinforced concrete structures (cellars, high-rise buildings etc.), the DCF signal reception is weaker, depending on the
conditions. In extreme cases, place the weather station close to a window toward the transmitter. Reception of the DCF77
radio signal is aected by the following factors:
• thick walls and insulation, basements and cellars
• unsuitable local geographic conditions (dicult to predict beforehand)
• atmospheric disturbances, thunderstorms
• appliances with no disturbance elimination
• television sets and computers placed near the DCF receiver
Manual Setting of Time and Other Indicators on the Weather Station
If you hold down the MODE button for 2 seconds, the year value will begin ashing. Using the UP/DOWN buttons, you can then
set: year; month; day; 12/24 hour mode; time zone; hours; minutes; day of the week language; °C/°F scale and nally hPa/inHg
pressure display unit. Set the desired values and units using the UP/DOWN buttons and move in the menu by pressing the
MODE button. If searching for radio signal is currently active, the setting mode cannot be used.
Calendar languages are as follows:
GE - German
EN - English
IT - Italian
FR - French
NE - Dutch
ES - Spanish
DA - Danish
Time/Date Display Mode
Pressing the MODE button switches between time and date on the display. After pressing the MODE button, the display will
show date instead of time and will switch back after 8 seconds.
Sensor Channel Change and Connecting Additional Sensors
1. Short press the UP button on the back of the weather station to select the desired sensor channel – 1, 2 or 3. Then long
press the UP button; the icon will start ashing.
2. Remove the cover from the battery compartment and insert batteries (2× 1.5 V AAA).
3. Use the CH button to set the desired sensor channel No. – 1, 2, 3 which will be shown on the front panel display. Data from
the sensor will be loaded within 3 minutes.
4. If the sensor signal is not detected, remove the batteries and reinsert them.
Displaying Maximum and Minimum Readings of Temperature and Humidity
Repeatedly pressing the DOWN button will gradually display the maximum and minimum readings of temperature and humidity.
In the MAX/MIN display mode, long press the DOWN button to delete the memory of values measured.
Atmospheric Pressure and Pressure Trend
The atmospheric pressure indicator to the right of the time shows with an arrow whether pressure is rising, stable or dropping
and shows the exact hPa/inHg value next to it. You can switch between the hPa and inHg pressure scale in the mode for manual
setting of time and other indicators on the weather station.
Indication on the display
Pressure trend rising constant falling
Setting and Activating Alarm
Repeatedly press the ALARM button. Values set for alarm 1 (A1) and alarm 2 (A2) will be displayed. To set or change the alarm
time, hold the ALARM button for 2 seconds, then set the time using the UP/DOWN buttons. The settings go in this order A1-hour
> minute > A2-hour > minute. Activate alarm 1, 2 or both using the DOWN button when the ALARM time is displayed on the
screen the display will show these icons:
.

Emos E0211 Specifications

General

Brand	Emos
Model	E0211
Category	Weather Station
Language	English