Emos TFE-5 - Page 3

3
a higher group number, whereas the se-
quence is as follows:
1ON1OFF2ON2OFF... 10ON10OFF
Real time will show automatically after 15 s
of inactivity in the settings or if you push the
CLOCK button.
3. After choosing the programme (1–10) you can
set the day of the week and the time. Push
WEEK to choose the day or a block of days in
a week. The abbreviations of days/blocks are
displayed in the following order:
3.1 MO TU WE TH FR SA SU
3.2 MOTUWETHFRSASU
3.3 MO TU WE TH FR
3.4 SA SU
3.5 MO TU WE TH FR SA
3.6 MO WE FR
3.7 TU TH SA
3.8 MO TU WE
3.9 TH FR SA
3.10 MO WE FR SU
4. To set the time of the programme, the LCD
must be showing the “PROGRAM” text.
4.1 To set the time of the start (turn on) the pro
-
gramme (1ON) push the HOUR button briey
and the hours will start changing slowly. If
you hold this button, hours will change fast.
Release the button as soon as the desired hour
appears on screen.
4.2 To set the minutes of the programme start
(1ON), push the MINUTE button and the
time will start changing slowly. If you hold
the button, time changes fast. Release the
button as soon as the desired minute value
appears on screen.
4.3 To set the programme end (turn o) (1OFF)
push the TIMER button and proceed the same
way as described in points 4.1 and 4.2
Note: (a) If you want to adjust a pre-set pro
-
gramme, proceed like in points 4 to 4.3 in part F
and enter new data to replace the original setting.
(b) After setting the programme, push CLOCK
to return to the real time display. If you do not
do so, the time will automatically show after 15
seconds of inactivity.
Random
1. The Random function turns the appliance on
and o irregularly every 10 to 31 minutes
from 18:00 to 6:00.
2. Plug the switch to the electric socket and
use the ON/AUTO/OFF button to set the
programme to the AUTO mode, so you can
start/end the Random function.
3. Push the RANDOM button and the right part
of LCD will display an “R” symbol to indicate
the random turn o/on function is activated.
For 10–31 minutes the power supply is o.
After this time the function switches to an
opposite mode, so it turns on.
4. By repeated pushing of the RANDOM button
you can suspend the function of random
turning on/o and the “R” sign will disappear
from the display.
Cancelling/restoring a pre-set
programme
When you push ON/AUTO/OFF, you can cancel/
restore a pre-set programme, so the display will
change in the following order:
1. “ON” cancelling a pre-set programme, so
the appliance will remain on all the time.
2. “AUTO” restoring a pre-set programme, so the
appliance will go turning on and o automat
-
ically according to the settings.
3. “OFF” cancelling a pre-set programme, so the
appliance will remain o all the time.
Note:
(a) The pre-set function of random activation/
deactivation will work only if the switch is in the
AUTO mode.
(b) If the Random function is activated, the auto
on/off functions of the set programmes are
inoperative.
Installation
1. Set the required on/o programmes at the
switch, as described above.
2. Turn the electric appliance o.
3. Plug the supply cable of the appliance into
the socket of the switch and then connect
the switch to the power supply.
4. Turn the appliance on.
5. The appliance will be on/o according to
the programmes, you chose, unless you
push manual cancelling of the setting.
SAFETY WARNINGS
• If the screen isn’t working, plug the timer
socket into a 230 V AC socket and let it
charge – the screen should light up in about
2 hours and the socket should be fully
functional. To recharge fully, leave it in the
socket for approx. 12 hours.
• The device must only be connected to and
used with 230 V AC (~)/50 Hz electrical
wiring tted with a protective contact in line
with valid electrical regulations.
• Pay attention to the data on the type label
of the appliances connected to the device.