EMT 929 User Manual

ELEKTRONIK-
MESS- UND
TO NSTU DI OTECH NI K
MONTAGEANLEITUNG
Tonarm EMT929
für EMT 930
Der Stereo/Mono-Tonarm EMT 929 ist statisch und dyna-
misch ausbalanciert. Es ist möglich, wahlweise T-Tondosen
(Stereo) oder OF-Tondosen (Mono) zu verwenden.
Er ersetzt also die bisherigen Ortofon-Tonarme RF 229-
Mono und RMA 229(s)-Stereo.
Auf Wunsch kann für die Stereo-Abtastung eine Anti-
skating-Vorrichtung benutzt werden.
Im Styroporbehälter befinden sich folgende Teile:
Tonarm EMT 929,
Tonarmsockel mit Befestigungsteilen,
Anschlußleitung mit 7-po1igem Stecker,
Gegengewicht auf Rohrstück mit Befestigungs-
schraube,
Mono-Ausgleichsgewicht,
Antiökatinggewicht,
Höhen-Einstell-Lehre,
2-mm-Inbusschlüssel,
Auflagebank der Tonarm-Hebe/Senk-Vorrichtung.
Hinweis: Wird der Tonarm EMT 929 gegen einen des
gleichen Typs ausgetauscht, so sind die Angaben
erst ab Punkt 6. zu beachten.
Wird der Tonarm auf einem Plattenspieler anderen Fa-
brikats montiert, so ist der Abstand von 230 mm zwi -
schen Plattenteller- und Tonarmsockel-Mittelpunkt
zu beachten.
MOUNTING INSTRUCTlüNS
Pick-up arm EMT 929
for EMT 930
The Stereo-Mono Pick-up arm EMT 929 is statically and
dynamically balanced. Either T-pick-up heads (stereo)
or OF-pick-up heads (mono) may be used.
This pick-up arm replaces the Ortofon pick-up arms RF
229-mono and RMA 229 (s)-stereo, which have been in
use until now.
For stereo reproduction an anti-skating device may be
used if desired.
The Styropor container contains the following parts:
Pick-up arm EMT 929
Pick-up arm socket with fixing parts
Connecting lead with 7-po1e plug
Counter-weight on tube with locking screw
Mono balancing weight
Anti-skating weight
Height adjustment gauge
2mm allen key
Support for the pick-up arm lowering device
Note: If the pick-up arm EMT 929 is a replacement for
an arm of the same type, the following instructions
should be followed from paragraph 6 onwards only.
In case the pick-up arm should be mounted on a turn-
table of other origin, a center distance of 230 mm bet-
ween turntable and arm socket should be adjusted.
7-po1.
Tonarm-
Stecker
7-po1e
tone arm
connector
Höhen-Einstell-
Lehre
Height adjustment
gauge
Inbus-
Schrauben
Allen screws
Antiskatinggewicht
Anti-skating weight

EMT 929 Specifications

General

Brand	EMT
Model	929
Category	Turntable
Language	English

Summary

Mounting Instructions for Pick-up Arm EMT 929

Introduction to EMT 929 Pick-up Arm

Static/dynamic balance, T/OF head compatibility, and replacement of Ortofon arms.

Included Parts in Container

Lists all components provided in the Styropor container.

Special Mounting Notes

Notes for same-type replacement or mounting on different turntables.

Installation Steps

Removal of Existing Pick-up Arm

Steps to remove the old pick-up arm, stop pin, support bolt, and lowering device support.

Fitting New Socket and Connecting Cable

Mounting the new socket and soldering the connecting lead to the equalizer amplifier.

Arm Height Adjustment and Flange Fitting

Aligning the arm bearing, setting height with gauge, and securing in the flange.

Fitting the Counter-weight

Attaching the counter-weight to the rear end of the pick-up arm tube.

Balance Adjustment Procedure

Balancing the arm for T-pick-up (stereo) or OF-pick-up (mono) cartridges.

Playing Weight Adjustment

Setting the tracking force lever according to cartridge type and weight.

Anti-skating Device

Explains skating force and how to fit the anti-skating weight for stereo cartridges.

Adjustments and Diagrams

Stereo Cartridge Adjustments

Details balance, playing weight, and anti-skating settings for T-series stereo cartridges.

Mono Cartridge Adjustments

Details balance and playing weight settings for OF-series mono cartridges.

Component Identification

Identifies parts like the tracking force adjustment lever, tone arm lift, and specific cartridge types.