ENDA ET2011 - User Manual

230V AC+%10-%20,50/60Hz 24V AC%10,50/60Hzor
Max. 5VA
Power : ,Si :1 ²connector 2.5mm²'screw-terminal gnalconnector ,5mm screw-terminalconenction.
EEPROM( )minimum10years
Max. 100ohm
1 bit2
00ms1
R :250V AC,8A (forresistiveload),SelectableasNO+NCControlor Alarm2output.elay
°C
Withotload30.000.000mechanicaloperation;250V AC,onthe8Aresistiveload100.000
electricalswitching
C/A2output
ENDA ET2011PIDTEMPERATURECONTROLLER
* x mm .77 35 sized
Thankyouforchoosing 2011temperaturecontroller.ENDA ET
TECHNICAL SPECIFICATIONS
* Selectabledual-setvalue.
*Se tlectablethermocouple ypesorPt100input.(Selectionmustbe
*Soft-Start feature.
* (SELFTUNE).AutomaticcalculationofPIDparameters.
*Selectableheating/coolingcontrol.
* C/A2Relayoutputcanbeprogrammableasalarmorcontroloutput.
* .SelectableSSRcontroloutput
* Inputoffsetfeature.
* Inthecaseofsensorfailureperiodicalrunningorrelaystatecanbe
selected.
* .CEmarkedaccordingtoEuropeanNorms
Inputtype Temperaturerange
J(Fe-CuNi) Thermocouple
K(NiCr-Ni)Thermocouple
T(Cu-CuNi)Thermocouple
S(Pt 0Rh-Pt)T1 hermocouple
R(Pt13Rh-Pt)Thermocouple
EN60584
EN60584
EN60584
EN60584
EN60584
0...600
0...1300
0...400
0...1700
0...1700
°C
°C
°C
°C
°C
Accuracy
0, %( )5 offullscale
0, %( )5 offullscale
1 digit
1 digit
0, %( )5 offullscale 1digit
0, %( )5 offullscale 1digit
0, %( )5 offullscale 1digit
+32...+1112
+32...+2 237
+32...+752
+32...+3092
+32...+3092
°F
°F
°F
°F
°F
°C
°F
SSRoutput
Max20mA 12Volt(ascontroloutput)
SET
°C
SET
ET2011
ENDA
°F
C/A2
SSR
F
Pt100Resistancethermometer
Pt100Resistancethermometer
EN60751
EN60751 -200...600°C
-328...1112°F
- ... 00 °C99.93 .0
- ...543 °F99.9 .0
0,5%(offullscale)
1 digit
0,5%(offullscale) 1digit
specifiedinorder).
EnterPIDparametersofthesystemiftheyareknownatthebeginning.
Otherwise,Self-Tuneshouldbeactivated.
ENVIRONMENTAL CONDITIONS
Height
Max.2000m
80 upto31decreasinglinearly50 at40.% %
Ambient/storagetemperature
Max.Relativehumidity
0...+50 /°C-25...+70°C(withnoicing)
Ratedpollutiondegree
AccordingtoEN60529Frontpanel:IP65
Rearpanel:IP20
Donotusethedeviceinlocationssubjecttocorrosiveandflammablegases.
OUTPUTS
Lifeexpectancyforrelay
ELECTRICAL CHARACTERISTICS
Supply
Powerconsumption
Wiring
Lineresistance
Dataretention
EMC
Safetyrequirements
EN61326-1:2006
EN61010-1:2010(Pollutiondegree2,overvoltagecategoryII)
CONTROL
Controltype
Singleset-pointandalarmcontrol
Controlalgorithm
A/Dconverter
Samplingtime
Proportionalband
Controlperiod
Hysteresis
Outputpower
Adjustablebetween0 and100 .IfPb=0 ,On-Offcontrolisselected.% % %
and250secondsAdjustablebetween1
1and50Adjustablebetween °C/F
Theratioofpoweratasetpointcanbeadjustedbetween0 and100% %
HOUSING
Housingtype
Suitableforflush-panelmountingaccordingtoDIN43700.
Dimensions
W77xH35xD71mm
Weight
Approx.200g(afterpacking)
Selfextinguishingplastics.
Enclosurematerial
Whilecleaningthedevice,solvents(thinner,benzine,acidetc.)or mustnotbeused.corrosivematerials
Readthisdocumentcarefullybeforeusingthisdevice. Theguaranteewillbeexpiredby
damagingofthedeviceifyoudon'tattendtothedirectionsintheusermanual. Alsowedon't
acceptanycompensationsforpersonalinjury,materialdamageorcapitaldisadvantages.
R :250V AC,16A (forresistiveload),SelectableasNOControlor Alarm2output.elay
ET -E2011
1./4
english
uptodate:01022014,modificationreservedandcanbechangeanytimepreviousnotice!

Summary

Technical Specifications Overview

Environmental and Electrical Characteristics

Details on ambient/storage temperature, humidity, pollution, supply voltage, power consumption, wiring, EMC, and safety.

Output and Control Parameters

Specifications for C/A2, SSR outputs, relay life, control types, algorithms, sampling times, and output power.

Housing and Dimensions

Information on the housing type, physical dimensions, weight, and enclosure material.

Programming Mode and Parameter Navigation

Parameter Diagram and Navigation

Guidance on navigating the parameter diagram and understanding the display indicators.

Self Tune and Default Parameters

Explanation of the automatic PID parameter calculation (Self Tune) and default settings.

Alarm Configuration and Set Point Modification

Alarm2 Output Types

Details on different Alarm2 output configurations: Independent, Deviation, and Band alarms.

Modifying Control and Alarm Set Points

Instructions on how to change the control and alarm set points using the keypad.

Error Messages and Troubleshooting

Explanation of common error messages (PFA, PSC) and their meanings.

Installation and Connection

Dimensions and Panel Cut-out

Physical dimensions, mounting clamp, and panel cut-out requirements for installation.

Connection Diagram and Wiring

Diagram illustrating input selection, supply voltage, and output connections.

Safety and Installation Notes

Important safety precautions and notes for installation and wiring.

ENDA ET2011 Specifications

General

Input Type	Thermocouple, RTD
Output Type	Relay, SSR, Analog
Control Mode	ON/OFF, PID
Supply Voltage	100-240V AC
Display	4-digit
Resolution	0.1°C
Communication	RS485