Energizer 341 User Manual

Chemical System: Silver Oxide (Zn/Ag
2
O)
Nominal Voltage: 1.55 Volts
Typical Capacity: 13 mAh* (to 1.3 volts)
Capacity Test: 68K ohm continuous drain at 21°C
Typical Weight: 0.29 grams (0.009 oz.)
Typical Volume: 0.07 cubic centimeters (0.004 cubic inch)
Impedance (40 Hz): 35 to 45 ohms
Load
Cutoff
1.3V
(ohm) (hours)
68K 565
Typical Performance at 21°C (70°F)
mm (inches)
Typical Discharge Characteristics
at 1.55V
(milliamperes)
Schedule
Typical Drains
©Energizer Holdings, Inc. - Contents herein do not constitute a warranty.
Im
p
ortant Notic
e
This datasheet contains typical information specific to products manufactured at the time of its publication.
Continuous 0.023
Industry Standard Dimensions
ENERGIZER 341
Typical Performance at Low Discharge Rates
Temperature Characteristics
SILVER OXIDE
Specifications
Cross Section
* Varies according to the applied load, temperature, and cutoff voltage.
PRODUCT DATASHEET
1-800-383-7323 / USA
1-800-383-7323 / CANADA
1-800-383-7323 USA/CAN
www.energizer.com
Schedule: Continuous
Typical Drain @1.55V:
0.023 milliamperes
Load: 68K ohm
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
0 150 300 450 600
Service, Hours
Voltage, CCV
DESIGNED FOR USE ON CONTINUOUS LOW DRAIN
Service Effects
0
25
50
75
100
125
-20 0 20 40
Temperature (C)
Service (%)
Storage Effects
60
70
80
90
100
024681012
Storage Time (yrs)
Service (%)
40°C
20°C
0°C
Anode Cap
Gel Anode
Gasket
Can
Separator
Cathode
7.90 (0.311)
7.62 (0.300)
R0.40 (0.016)
Typical
0.02 (0.001) Minimum Ref.
(applies to top edge of gasket or
edge of crimp, whichever is higher)
6.20 (0.244) Ref.
Typical
1.30 (0.051)
1.45 (0.057)
1.40 (0.055) Ref.
1.20 (0.047) Ref.
0.15 (0.006) Maximum Ref.
Permissible deflection from a flat
Form No. EBC - 4315E Page 1 of 1

Energizer 341 Specifications

General

Brand	Energizer
Model	341
Category	Camera Accessories
Language	English

Summary

Energizer 341 Specifications

Chemical System

Specifies the battery chemistry as Silver Oxide (Zn/Ag2O), indicating the materials used in its construction.

Nominal Voltage and Capacity

Details the battery's standard voltage output and its typical energy capacity in mAh, with a note on voltage variation.

Capacity Test Conditions

Outlines the conditions under which the battery's capacity is tested, including continuous drain and temperature.

Physical Characteristics

Provides the typical weight and volume of the battery in both metric and imperial units for reference.

Electrical Impedance

States the typical internal impedance of the battery when measured at a specific frequency (40 Hz).

Product Dimensions and Design

Industry Standard Dimensions

Illustrates the battery's dimensions in millimeters and inches, showing key measurements and tolerances.

Cross Sectional View

Presents a cutaway view of the battery, labeling its internal components like anode, cathode, and separator.

Design Intent

Highlights that the battery is specifically designed for continuous low drain applications.

Battery Performance Characteristics

Typical Discharge Characteristics

Shows how the battery voltage performs over time under specific continuous drain conditions at 21°C.

Temperature Effects on Service

Illustrates how service capacity is affected by different operating temperatures at low discharge rates.

Storage Effects on Service

Depicts the impact of storage time and temperature on the battery's remaining service capacity.