Chapter 3ÑGlobal Settings
ENSONIQ ZR-76 Musician's Manual 35
You can change the routing of the insert, global chorus, global reverb, and dry effect busses. Each of
these effect busses can be routed either to:
¥ MainÑthe ZRÕs primary outputs ¥ AuxÑthe ZRÕs additional outputs
5. Turn the Value knob to route the effect bus you selected to the desired output.
DD
DD
ee
ee
tt
tt
ee
ee
rr
rr
mm
mm
ii
ii
nn
nn
ii
ii
nn
nn
gg
gg
tt
tt
hh
hh
ee
ee
BB
BB
ee
ee
hh
hh
aa
aa
vv
vv
ii
ii
oo
oo
rr
rr
oo
oo
ff
ff
tt
tt
hh
hh
ee
ee
AA
AA
uu
uu
xx
xx
OO
OO
uu
uu
tt
tt
ss
ss
The Aux Outs are used for the extraction of sounds from the Main Outs mix. The ZR-76 is designed to
provide the maximum flexibility when using the Aux Outs in your rig. The AuxToMainOuts System
parameter offers three different ways to employ the Aux Outs. You can choose which one will work best
for you.
When AuxToMainOuts is set to Auto, the ZR employs intelligent jack switching, which allows it to sense
whether or not youÕve got a cable plugged into the Left Aux Out jack. If you do, the Main and Aux Outs
function as totally discrete stereo feeds. If thereÕs nothing connected to the jack, any signal sent to the
Aux Outputs will be summed into the Main Outputs. This is convenient for musicians who seek to keep
mixer input use to a minimum, or who anticipate using the Aux Outs only rarely.
Musicians who would prefer to permanently connect all four ZR keyboard outs will find the remaining
two AuxToMainOuts values useful. When the parameter is set to Never, the Aux and Main Outs are kept
discrete. When itÕs set to Always, the Aux Outs are summed into the Main Outs. This allows musicians to
leave all four ZR-76 output cables connected. When the Aux Outs are needed as a separate stereo feed,
the AuxToMainOuts parameter can be set to Never. When only the Main Outs are required, it can be set
to Always.
When you change any system setting, ZR-76 operations will pause momentarily
to store your settings into FLASH memory.
TT
TT
oo
oo
EE
EE
nn
nn
aa
aa
bb
bb
ll
ll
ee
ee
AA
AA
uu
uu
tt
tt
oo
oo
mm
mm
aa
aa
tt
tt
ii
ii
cc
cc
AA
AA
uu
uu
xx
xx
OO
OO
uu
uu
tt
tt
RR
RR
oo
oo
uu
uu
tt
tt
ii
ii
nn
nn
gg
gg
BB
BB
aa
aa
ss
ss
ee
ee
dd
dd
oo
oo
nn
nn
CC
CC
aa
aa
bb
bb
ll
ll
ii
ii
nn
nn
gg
gg
1. Press the System button.
2. Turn the Parameter knob until the display shows:
System/MIDI:
Set system prefs?
3. Press Yes if youÕd like to change the current system preferences. Press No if youÕd like to cancel the
procedure.
4. Turn the Parameter knob until the display shows:
System Preferences:
AuxToMainOuts= Auto
i
The current AuxToMainOuts value
The AuxToMainOuts parameter can be set to:
¥ NeverÑthe Aux and Main Outs will be discrete, even if the Left Aux Out is not connected.
¥ AlwaysÑthe Aux signal will be summed into the Main outputs, even if the Left Aux Out is
connected.
¥ AutoÑthe ZR-76 will sum any sounds sent to the Aux Outs into the Main Outs if thereÕs no cable
To Next Page
Loading...
