Epson Expression 1680 Start Here

Start Here
1 Make sure you have everything:
2 Remove all the packing tape, but leave the two yellow stickers in place
until instructed to remove them.
Unpack Your Scanner
Turn over
1
Scanner
CD-ROM with
EPSON
®
Scan driver
and electronic manual
Power cord
Wait! You must install your software before connecting the scanner
to your computer.
Be sure to close all open programs and turn off any virus
protection programs.
Windows
®
1 Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
The installer starts automatically.
If it doesn’t start, double-click My Computer (in Windows XP,
click Start > My Computer), double-click EPSON, then double-click
EPSON.
2 You see a message to close all running applications. Click OK.
3 Read the license agreement, then click Agree.
4 At the Software Installation screen, click Install.
5 Wait for Epson Scan and the User’s Guide to be installed.
6 At the last screen, click Exit. The EPSON Product Registration
screen appears.
7 Register your scanner as instructed. When finished, click Done
or close your browser. Remove your CD-ROM.
Install the Software
2
EPSON Expression
®
1680
USB cable
STOP: Be sure to install your scanner software first
BEFORE you connect the scanner!
See your Start Here sheet for details.
IMPORTANT!
Leave the stickers in place until
you are instructed to remove them.
Macintosh
®
1 Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
(If necessary, double-click the EPSON CD-ROM icon to open it.)
2 Double-click .
3 You see a message to close all running applications. Click OK.
4 Read the license agreement, then click Agree.
5 When the Software Installation screen appears, click Install.
6 Follow the on-screen instructions to install your User’s Guide.
When you’re done installing the User’s Guide, click Quit.
7 In Mac
®
OS X, enter your Administrator name and password when
prompted and click OK.
8 Read the license agreement, then click Accept.
9 When you see the EPSON Scan Installer screen, select EPSON
Expression 1680 in the Easy Install menu and click Install.
10 Mac OS X: At the last screen, click Exit. The EPSON Product
Registration screen appears.
Mac OS 8.6-9.x: When you’re done installing, restart your Macintosh.
The EPSON Product Registration screen appears when your
system restarts.
11 Register your scanner as instructed. When finished, click Done
or close your browser. Remove the CD-ROM.
Click Install
Click Install
Click Install
3
Connect the Scanner
After your software is installed, it’s time to get connected.
1 Remove the yellow tape from the back of the scanner.
2 Slide the transportation lock to the UNLOCK position.
Caution: Your scanner won’t work unless the transportation lock is in
the UNLOCK position. Also, you may damage the scanner if you leave
it on while it’s locked.
3 Connect the scanner to your computer. Use either the USB cable that
came with your scanner or a SCSI cable, if your computer has SCSI
support. Don’t connect both cables.
If you’re using USB...
Plug the square end of the USB cable into the scanner’s
USB port. Plug the flat end into any available USB port
on your computer or USB hub. Then go to step 4.
Note: Your scanner may not work correctly if you use a USB cable
other than the one supplied by EPSON, of if you connect your scanner
to a multi-level USB hub system.
STOP: Be sure to install your scanner software first
BEFORE you connect the scanner!
See your Start Here sheet for details.
If you’re using SCSI...
If you have another SCSI device that uses SCSI ID 2, turn the SCSI ID
switch on the back of the scanner to a new number. Do not use 0 or 7.
Unless your scanner is connected in the middle of a SCSI chain,
leave the terminator switch on the back of the scanner turned ON.
Squeeze the lock releases on your SCSI cable, and plug the cable into
either SCSI connector on the back of the scanner. Connect the pin end
of the cable to the SCSI port on your computer.
4 Plug one end of the scanner’s power cord into the AC inlet at the back
of the scanner, and the other end into a grounded electrical outlet.
5 Press the power button on the front of the scanner to turn it on.
The green READY light begins to flash. Wait for the flashing to stop.
6 If you have a USB connection, go to “Your First Scan” on the back of
this sheet.
If you have a SCSI connection, start the Add Hardware Wizard in the
Windows Control Panel and follow the on-screen instructions to let
Windows detect your scanner. Then continue with the instructions on
the back of this sheet to begin scanning.
continue
Click Agree

Epson Expression 1680 Specifications

Scanning Specifications

optical resolution	1600 x 3200 dpi
maximum resolution	13, 600 x 18, 720 dpi with interpolation
effective pixels	13, 600 x 18, 720 pixels (1600 dpi)
color depth	48 bits per pixel internal/external
grayscale depth	16 bits per pixel internal/external
scanning speed (color, 1600 dpi, draft mode)	9.2 msec/line (approx.)
scanning speed (grayscale/monochrome, 1600 dpi, draft mode)	3.1 msec/line (approx.)

Operating Environment

temperature operating range	41ºF to 95ºF (5ºC to 35ºC)
humidity operating range	10% to 80% (no condensation)
humidity storage range	10% to 85% (no condensation)

Power

voltage	AC 100V-120V, 220V-240V
frequency	50-60Hz
power consumption (operating without optional unit)	60W
power consumption (operating with optional unit)	75W
power consumption (standby without optional unit)	10W

Weight and Dimensions

maximum read area	8.5" x 11.7" (216mm x 297mm)
width	13.1" (332mm)
depth	22.1" (562mm)
height	5.2" (133mm)
weight	18.7 lb (8.5 kg approx.)