Quick Setup
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
Note: These illustrations show the PowerLite X12, but the instructions are the
same for the S11 unless otherwise noted.
Connect the projector
Choose from the following connections. See the sections below or the User’s
Guide on your projector CD for details.
Computer
USB Port
Connect the square end of a USB cable to the projector’s USB TypeB
(square) port. Connect the flat end of the cable to any USB port on your
computer.
Windows
®
2000 SP4 or later: After turning on the projector, follow
the on-screen instructions to install the Epson USB Display software
(EMP_UDSE.EXE; only on first connection). If the software screen does not
display automatically, open My Computer or Computer, then double-click
EPSON_PJ_UD.
Mac OS
®
X 10.5.1 or higher: After turning on the projector, the setup folder
for USB Display appears in the Finder. Double-click USB Display Installer and
follow the on-screen instructions to install the Epson USB Display software
(only on first connection).
Note: If you have problems installing the USB Display software on the
PowerLite X12, make sure the USB Type B setting in the projector’s Extended
menu is set to USB Display. See the User’s Guide on your projector CD for
instructions.
Monitor Port
Connect one end of a VGA cable to the projector’s Computer port, and the
other end to your computer’s monitor port. If you are using a laptop,
switch it to external display (see “Troubleshooting”). You can also connect an
audio cable.
HDMI Port (X12)
Connect one end of an HDMI cable to the projector’s HDMI port and the other
end to an HDMI port on your computer.
Video Device
Connect up to 3 (S11) or 4 (X12) video devices and use the remote control to
switch between them. (HDMI is not available for the S11.)
RCA video cable (composite video)
Component video to VGA cable
S-Video cable
Audio cable
HDMI cable
Camera, USB Device, or Epson Document Camera DC-06
Connect a digital camera, USB flash drive, USB storage device, or Epson
document camera DC-06 to the projector’s USB TypeA (flat) port.
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s Slideshow feature. See the User’s Guide on your projector CD
for details.
Turn on your equipment
1
Turn on your computer or video source.
2
Plug in the projector. The power light on the projector turns orange.
3
Open the lens cover all the way.
4
Press the power button on the projector or remote control. The
projector beeps, the power light flashes green, and then stays on.
Note: To shut down the projector, press the power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
5
The default language of the menu system is English. To select another
language, press the Menu button on the remote control. Select
Extended and press Enter. Select Language and press Enter. Select
your language and press Enter. Press the Menu button to exit the menu
system.
Adjust the image
1
If you don’t see an image, press the Source Search button on the
projector or remote control to select the image source.
Note: If you still see a blank screen or have other display problems, see the
troubleshooting tips on the right.
2
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
3
X12: To reduce or enlarge the image, turn the zoom ring.
S11: To reduce or enlarge the image, press the Tele (reduce) or Wide
(enlarge) buttons on the projector. You can also use the Zoom option in
the projector’s Settings menu. See the User’s Guide on your projector CD
for details.
X12
S11
4
Turn the focus ring to sharpen the image.
X12
S11
5
If your image looks like or , you’ve placed the projector off to
one side of the screen at an angle. Place the projector directly in front
of the center of the screen, facing the screen squarely, or do one of the
following:
X12: Use the horizontal slider on the projector to correct it.
S11: Press the or button on the projector. Then press the
Tele or Wide button to correct it.
X12
S11
6
X12: Your projector automatically adjusts images that look like
or , but if necessary you can press the or button
on the projector to correct it.
S11: If your images look like or , press the or button
on the projector to correct it.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
For more information on using the remote control, see the User’s Guide on
your projector CD.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
•
Make sure the power light on the projector is green and not flashing,
and the lens cover is open.
•
Press the Source Search button on the projector or the remote control
to switch to the correct image source, if necessary.
•
If you’re using a Windows laptop, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as . You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
•
If you’re using a Mac
®
laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary,
then click the Arrange or Arrangement tab, and select the Mirror
Displays check box.
Where to get help
Manual
For more information about using the projector, install the User's Guide from
your projector CD.
Telephone Support Services
To use the Epson PrivateLine
®
Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 a m to 6 p m , Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
US: (562) 276-4394, 6 a m to 8 p m , Pacific Time, Monday through Friday, and
7 a m to 4 p m , Pacific Time, Saturday
Canada: (905) 709-3839, 6 a m to 8 p m , Pacific Time, Monday through Friday
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
Visit www.epson.com/support (US) or www.epson.ca/support (Canada)
for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates, special promotions and customer-only
offers. You can use the CD included with your projector, or register online at
www.epson.com/webreg.
PowerLite
®
S11/X12
Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson
Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2011 Epson America, Inc. 5/11
Printed in XXXXXX CPD-34835
USB cable
HDMI cable
VGA cable
Turn projector
on and off
Access projector
menus
Choose which
source to display
Navigate projector
menus
Get solutions to
common problems
Turn off projector
display
To Next Page
Need help?
General
Weight and Dimensions
