Epson Stylus NX125 Series User Manual

Start Here
2 Lower the output tray, then open the extension.
3 Flip the feeder guard forward.
4 Squeeze the edge guide and slide it to the left.
5 Load paper against the right edge guide and behind the
tab, with the printable side face up.
4 x 6
8½ x 11
Read these instructions before using your printer.
1
Unpack
Power cord
Epson Stylus NX125/127
Series
Quick Guide
Basic Copying, Printing, and Scanning
Maintenance
Solving Problems
®
Caution: Do not open the ink cartridge package until you are ready to
install the ink. Cartridges are vacuum packed to maintain reliability.
Remove all protective materials.
2
Turn on
1 Connect the power cable.
Caution: Do not connect to your computer yet.
2 Press the power button.
3
Install ink cartridges
1 Open the document cover, then open the ink cover.
Caution: Don’t try to remove the ink cartridge guard or you may
damage the printer.
2 Shake the ink cartridges, then unpack them.
3 Remove only the yellow tape from each cartridge.
Caution: Don’t remove any other seals from the cartridges.
4 Insert the cyan ink cartridge, and press it down until it clicks.
5 Press the stop button. The cartridge holder moves.
6 Repeat steps 4 and 5 for other cartridges.
7 Close the ink cover, then close the document cover and
press the stop button again.
8 Ink priming takes about 2 minutes. When the green power
light stops blinking, priming is complete.
Note: Your printer ships with full cartridges and part of the ink
from the first cartridges is used for priming the printer.
Caution: Don’t turn off the printer while it is priming or you’ll
waste ink.
4
Load paper
1 Open the paper support, then pull up the extension and tilt
it back slightly.
Epson Stylus
®
NX125/127 Series
4119074 Rev.0
1-F C
4119074 Rev.0
1-F M
4119074 Rev.0
1-F Y
4119074 Rev.0
1-F K

Epson Stylus NX125 Series Specifications

General

Print Technology	Inkjet
Functions	Print, Copy, Scan
Scanner Type	Flatbed color image scanner
Connectivity	USB 2.0
Input Capacity	100 sheets
Output Capacity	30 sheets
Print Resolution	5760 x 1440 dpi
Scanner Resolution	600 x 1200 dpi
Operating Systems Supported	Windows and Mac OS
Paper Sizes	A4, A5, A6, B5, Letter, 4x6, 5x7
Copy Resolution	600 x 600 dpi
Power Consumption	Approx. 12 W (ISO 24712)

Summary

Unpack and Power On Printer

Unpack Printer and Components

Instructions for unpacking the printer, its power cord, and related accessories.

Turn On Printer

Steps to connect the power cable and press the power button to turn on the printer.

Install Ink Cartridges

Prepare Ink Cartridge Installation

Open document and ink covers, shake cartridges, and remove yellow tape before installation.

Insert Ink Cartridges

Insert cyan ink cartridge until it clicks and press the stop button to move the holder.

Complete Ink Priming

Repeat cartridge installation, close covers, and allow ink priming to complete.

Load Paper into Printer

Prepare Paper Feeders

Open paper support, extensions, and feeder guard, then adjust the edge guide.

Load Paper Correctly

Load paper against the right edge guide with the printable side facing up.

Finalize Paper Loading

Slide edge guide against paper and flip feeder guard back.

Install Printer Software

Prepare for Software Installation

Ensure printer is not connected to the computer and handle any found hardware prompts.

Run Software Installation

Insert the software CD, run SETUP.EXE, and follow on-screen instructions.

Connect and Add Printer

Connect the USB cable when prompted and add the printer via the OS interface.

Additional Information and Support

Access User's Guide and Support

Find the User's Guide, technical support, drivers, FAQs, and contact information.

Paper and Ink Recommendations

Information on using Epson premium papers and genuine Epson ink cartridges.