EQUIFAB P185 - User Manual

To Next Page

Guide d’utilisation

Equifab

Épandeur en polyéthylène Épandeur en inox.

P185 et P210 S100, S175, S200 et S300

POIDS MOYEN DES ABRASIFS

MATÉRIEL POIDS (VERGE CUBE)

Sel (Sec) 2500 lb

Sable / Sel (50/50) 3000 lb

ATTENTION :

Il est très important de ne pas surcharger votre véhicule. Vérifier avec le manufacturier

la capacité de charge du camion avant de remplir l'épandeur.

Mesures de sécurité

Il est très important de lire, de comprendre et d’appliquer ces mesures de sécurité avant

d'utiliser l'épandeur.

En respectant ces règles, vous diminuerez les risques de blessures ainsi que les bris

mécaniques.

1- Lire ce document en entier avant d'utiliser votre épandeur.

2- Assurez-vous que toutes les composantes de sécurité sont bien fixées sur l'épandeur

avant de mettre en opération.

3- S'assurer qu'il n'y ait personne autour de l'épandeur avant de le mettre en fonction.

4- Ne pas dépasser la capacité de charge de votre véhicule. Si vous avez des doutes,

contactez votre concessionnaire.

5- Si vous devez ajuster, laver ou lubrifier votre épandeur, assurez-vous que la source

de courant est déconnectée (batterie) avant de commencer les travaux.

6- Ne pas monter sur l'épandeur pendant qu'il est en fonction.

7- S'assurer que l'épandeur est fixé de façon sécuritaire au camion (boulonné). Important:

Consulter un installateur compétent avant toute utilisation. Utiliser des tendeurs avec

chaînes.

8- Ne jamais utiliser votre épandeur s'il est défectueux.

9- Ne jamais laisser du matériel dans la cuve pour une longue période. Le matériel peut

geler et endommager l'épandeur.

10- Toujours déconnecter la batterie avant de remplacer des composantes mécaniques ou

électriques.

11- Vérifiez les boulons d'assemblage régulièrement pour s'assurer qu'ils sont bien fixés.

Owner’s Manual

Equifab

Polyethylene spreader Stainless steel spreader

P185 and P210 S100, S175, S200 and S300

AVERAGE MATERIAL WEIGHTS

MATERIAL WEIGHT (PER CUBIC YARD)

Salt (Dry) 2500 lb

Sand / Salt (50/50) 3000 lb

WARNING

Do not overload, do not exceed your truck capacity. If you don’t know your truck capacity, verify with

the manufacturer before filling the spreader.

SAFETY PRECAUTIONS and WARNINGS:

It is very important to read and to understand these safety precautions and warnings. By doing so,

you will avoid any risks of injuries or mechanical break downs.

1- Read this entire owner’s manual before operating this spreader.

2- Make sure that all safety components are securely mounted and in place before operating this

spreader. Make sure that the spreader is sitting flat on the truck body.

3-Make sure that no one is around the spreader spray area before starting or operating this

spreader.

4- Do not over-load your vehicle beyond its capacity. If there are any questions, contact the

vehicle manufacturer.

5- Do not adjust, clean, lubricate or do any work on the spreader without first turning off the power

source (battery).

6- Do not climb on or in the spreader during operation. Do not ride on the spreader while the

vehicle is in motion.

7- Make sure that the spreader is securely fastened to the vehicle. Important: Installation must be

done by a qualified person. Use turnbuckles with chains to fix the spreader in the truck.

8- Do not operate a spreader that is in need of maintenance or repairs.

9- Never leave any material in the hopper for extended period of time. Material may freeze and

seriously damage the spreader.

10- Always disconnect the battery before removing or replacing mechanical or electrical

components.

11- Verify regularly the mounting bolts for tightness

Main Page

Need help?

Do you have a question about the EQUIFAB P185 and is the answer not in the manual?

This document describes a spreader, available in both stainless steel and polyethylene models, designed for various spreading tasks. The manual provides detailed information on its function, technical specifications, usage, and maintenance.

Function Description

The device is a spreader, designed to distribute materials such as salt and sand. It is available in different models, including stainless steel (S175, S200, S300) and polyethylene (P185, P210). The spreader can be configured with either a single or dual motor system, depending on the model and desired spreading capacity. It is primarily used for spreading materials like salt and sand, with specific weight capacities for each material. The device is equipped with an electric system for operation, including an on/off switch and a power control kit for the motor(s).

Important Technical Specifications

Models:

Stainless Steel: S175, S200, S300
Polyethylene: P185, P210

Material Weights (per cubic yard):

Salt (Dry): 2500 lb (1134 kg)
Sand / Salt (50/50): 3000 lb (1361 kg)

Motor:

Type: 3/4 hp, 12 VDC
Control: Power control kits are available for 1 motor (VSCD-1W) and 2 motors (VSCD-2W).

Electrical System:

Voltage: 12 VDC
Circuit Breaker: 60A (for the on/off switch #765002)

Hopper Capacity:

The manual mentions a 625 ml (approximately 21 oz) oil level for the gearbox, indicating a significant capacity for material.

Usage Features

Pre-Operation Checks:

Before operation, it is crucial to read the entire owner's manual.
Ensure all safety components are securely mounted.
Verify that the spreader spray area is clear before starting.
Do not overload the spreader beyond its capacity.
Ensure the power source (battery) is fully charged.
Make sure the spreader is securely fastened to the vehicle.
Never leave the spreader in the hopper for extended periods.

Operation:

The spreader is controlled via an on/off switch and a power control kit, which manages the motor(s).
The power control kit allows for adjustment of the motor speed, influencing the spread pattern and density.
For optimal performance, ensure the oil level in the gearbox is checked regularly and maintained at 625 ml.

Safety Precautions:

Always be aware of potential hazards and warnings.
Avoid wearing loose clothing or jewelry that could get caught in moving parts.
Do not operate the spreader if any components are damaged or malfunctioning.
Ensure proper installation of electrical connectors using a wire crimper.

Maintenance Features

General Maintenance:

Regular Inspections: Inspect the spreader regularly for any signs of wear or damage.
Cleaning: Clean the spreader thoroughly after each use, especially the hopper and spreading mechanism, to prevent material buildup and corrosion.
Storage: When storing the spreader, especially during the summer season, it is recommended to cover the polyethylene tub with a tarp to protect it from UV damage and maintain its original color. Ensure the spreader sits flat and nothing is stacked on it to prevent deformation.

Electrical System Maintenance:

Dielectric Grease: Apply dielectric grease to all electrical connections during installation and regularly inspect and reapply as needed. This prevents corrosion and rust caused by saltwater infiltration.
Connector Cleaning: At the end of the season, clean and lubricate all connectors with dielectric grease.

Conveyor Chain Lubrication:

Initial Use: The conveyor chain does not require lubrication when the spreader is new.
End of Season Storage: Before storing the machine at the end of the season, it is crucial to lubricate the chain properly to prevent seizing. One method is to remove the chain and place it in a lubricant (such as waste oil or fuel).

Gearbox Maintenance:

Oil Level: Check the oil level in the gearbox every 2500 operating hours or every 6 months, whichever comes first. Use 625 ml of 75W90 semi-synthetic oil.
Oil Change: Never mix two different types of oil.
Breather Hole: Keep the breather hole in the filler plug (air-vent) clear to prevent pressure buildup.

Bearings Lubrication:

The purpose of bearing lubrication is to prevent direct metallic contact between rolling parts. Lubrication is essential to prevent premature degradation.
Use a grease gun to pump grease into the bearing until it comes out of the seal. Over-lubrication is not recommended.
If the bearing is hot, avoid lubricating it immediately; wait for it to cool down to prevent grease from overheating and leaking.

Mounting Bolts:

Inspect all regularly set screws and the mounting bolts for tightness because loose fasteners can cause misalignment and excessive wear.

This comprehensive guide ensures the safe and efficient operation, as well as the longevity, of the spreader.

EQUIFAB P185 Specifications

General

Brand	EQUIFAB
Model	P185
Category	Spreader
Language	English