ESPRIT 738 ultra User Manual

Esprit 728 Ultra & 738 Ultra - 1 - Programming Guide
System Programming Guide
Software Versions 4.4 (728ULT) and 4.1 (738ULT)
Installer Code (Default - 728 Ultra: 282828; 738 Ultra: 383838)
Full access to programming, except user access codes (PINs). No access to arming/disarming. Use only numeric keys from [0] to [9].
Zone Recognition
Streamlined Section Programming
This is an alternate method to Hex Programming (see page 2). Addresses 000 to 043 and 300 to 527 are grouped into 68 sections where
each section contains four addresses (i.e. section 00 = addresses 000 to 003). Using this method allows you to program 8 digits
(4 addresses) without having to exit and re-enter addresses.
The keypad will not display the current data in the Streamlined Section Programming method.
Table 1: Zone Recognition
Device connected to which input? 728 Ultra
No ATZ
728 Ultra
With ATZ
738 Ultra
No ATZ
738 Ultra
With ATZ
Control Panel
Input 1 = Zone 1 Zones 1 & 2 Zone 1 Zones 1 & 9
Input 2 = Zone 2 Zones 3 & 4 Zone 2 Zones 2 & 10
Input 3 = Zone 3 Zones 5 & 6 Zone 3 Zones 3 & 11
Input 4 = Zone 4 Zones 7 & 8 Zone 4 Zones 4 & 12
Input 5 = N/A N/A Zone 5 Zones 5 & 13
Input 6 = N/A N/A Zone 6 Zones 6 & 14
Input 7 = N/A N/A Zone 7 Zones 7 & 15
Input 8 = N/A N/A Zone 8 Zones 8 & 16
Keypad
Zone 1 = Zone 5 Zone 9 Zone 9 Zone 17
Zone 2 = Zone 6 Zone 10 Zone 10 Zone 18
Table 2: Streamlined Section Programming Method
1. Press [
ENTER] + [INSTALLER CODE] (Default - 728 Ultra: 282828; 738 Ultra: 383838) + [7].
2. The [
ENTER] and [2ND] keys will flash to indicate you are in programming mode (LED keypad only).
3. Enter 2-digit [
SECTION] (00 to 67).
4. The [ENTER] key will remain on while the [2ND] key will be off (LED keypad only).
5. Enter 8-digit [
DATA] to program the section.
6. The keypad will beep to indicate that the section has been programmed, data is saved and the
software has advanced to the next section.
7. Return to step 4 or press [
CLEAR] to exit programming mode.
&

ESPRIT 738 ultra Specifications

General

Brand	ESPRIT
Model	738 ultra
Category	Control Panel
Language	English

Summary

Zone Recognition

Streamlined Section Programming

Describes an alternate programming method using sections and 4 addresses.

Keypad Trouble Display

Hex Programming

Explains hexadecimal programming for system addresses and data entry.

INSTALLER / Panel Answer Options

Computer Telephone Number

Details programming the computer telephone number for system communication.

Monitoring Station Telephone Number 1

Instructions for programming the primary monitoring station phone number.

Monitoring Station Telephone Number 2

Instructions for programming the secondary monitoring station phone number.

Accounts "A" and "B"

Guide for programming account numbers for monitoring stations.

Arming Report Codes

Disarming Report Codes

Defines report codes for system disarming events and user activity.

Alarm Report Codes

Alarm Restore Report Codes

Specifies codes for when alarms are restored or cleared.

Shutdown Report Codes

Tamper Report Codes

Codes for tamper detection on the control panel or devices.

Trouble Report Codes

Codes indicating system malfunctions or operational issues.

Special Report Codes

Codes for specific events like panic, test, or system status.

Decimal Programming

Feature Select Programming

Telephone Line Monitoring (TLM)

Automatic Event Buffer Transmission

Configuration for system event buffer transmission.

Exclude Power Failure from Trouble Display

Setting to hide power failure events from the trouble display.

Key Access Programming

Connection Diagrams

Single Zone Connections

Diagrams illustrating single zone wiring without and with EOL resistors.

Advanced Technology Zone (ATZ) Connections

Other Connection Diagrams

Diagrams for keypad zone connections and parallel wiring.

728 Ultra Wiring Diagram

738 Ultra Wiring Diagram

Power Down Reset

Warranty

Provides warranty information and limitations for the product.

Notes