How to fix flexible motor pump coupling swells in Et Industrial Equipment?
If the flexible motor pump coupling swells, it's likely because the coupling has been soaked with oil. Replace the coupling and eliminate the oil leak; see Bulletin No. 100.
What to do if Et Industrial Equipment guiding device drifts in one direction?
If the guiding device drifts in one direction, it could be due to the following causes: * There may be no or low oil in the Hymod. If this is the case, fill or top up according to Bulletin No. 100. * The pump inlet strainer could be clogged. If so, replace the Hymod; see Bulletin No. 100. * The oil pump shaft might be binding. Replace the pump and inspect the spider for wear or damage.
How to fix Et Industrial Equipment power unit operating hot?
If your Et Industrial Equipment power unit is operating hot, consider the following: * The motor cooling intakes might be clogged; clean them out. * The ambient temperature may be too high; reduce the ambient temperature, relocate the power unit to a cooler location, or cool the unit with a fan during operation. * The oil level might be low; top up as necessary.
What to do if Et Industrial Equipment power unit will not start?
If your Et Industrial Equipment power unit won't start, it could be due to several reasons: * There may be no power to the motor; connect the power. * There could be a heater trip; reset the heater and determine the cause. * The contactors may not close; replace the contactors and the coil. * A capacitor might be blown; replace the capacitor. * There might be an open or shorted motor winding; replace or repair the motor; see Bulletin No. 100.
Why Et Industrial Equipment guiding device moves fast in one direction and slow in the other?
If the guiding device moves fast in one direction and slowly in the other, check these potential causes: * The S1 signal line could be cut or disconnected; replace or connect the line. * The S1 sensor orifice might be clogged; clean the orifice. * The blower filter may be clogged; clean or replace the filter.
How to fix wrinkle into rewind or out of unwind on Et Industrial Equipment adapter base?
If there's a wrinkle into the rewind or out of the unwind on the adapter base, it could be due to: * Not enough span between the base idler (or roll) and the last process idler; the span must be lengthened; Contact your E+L representative for further information. * A misplaced edge sensor; relocate the sensor.
What causes Et Industrial Equipment supporting knuckle of arcuate motion generator becomes loose?
If the supporting knuckle of the arcuate motion generator becomes loose and flops out of position, it's likely that the arcuate motion generator cable is broken. Repair the cable.
What causes Et Industrial Equipment idler bracket rocks?
If the idler bracket rocks, it's likely that the bracket retaining bolt is loose. Tighten the bolt.
What causes Et Industrial Equipment oil under power unit?
Oil under the power unit suggests a leak from the Hymod, oil pump, or fittings. Replace the leaking Hymod or oil pump; see Bulletin No. 100.
Why Et Industrial Equipment system generally unstable?
If your Et Industrial Equipment system is generally unstable, it might be because the signal lines are too short or pinched. Install lines of the proper length.
Devices that act directly upon the web to control its position.
Devices that sense web location and send corrective signals to actuators.
Basic interconnection of power unit, sensor, and servo cylinder.
Overview of the 400 Series WebAligner hydraulic power unit.
How the 400 Series WebAligner functions with edge detectors and servo-cylinders.
Guidelines for selecting an appropriate mounting location for the unit.
Instructions for electrical power connections, including motor rotation.
Procedures for connecting hydraulic lines to the unit.
Procedures for making pneumatic connections to the unit.
Guidelines for checking and maintaining hydraulic oil levels.
Cleaning or replacing the blower filter.
Step-by-step guide for replacing the Hymod unit.
Steps for removing and installing the motor assembly.
Guidance on replacing hoses, fittings, and other small parts.
Overview of hydraulic servo cylinders used in guiding systems.
Explanation of how servo cylinders function, including force and speed.
Guidelines for mounting servo cylinders on guiding devices.
Procedures for connecting hydraulic lines to the servo cylinder.
Instructions for replacing cylinder seal members.
What pneumatic sensors are and their variations.
How pneumatic sensors receive air and function.
Parameters for installing pneumatic sensors.
Installation parameters for porous sensing or three-leg sensors.
Procedure to check air flow from sensor jets.
Information on sensor repair and replacement.
Purpose and function of the Vernier Adjusting Bracket.
How to adjust the sensor position while the web is moving.
Summary of hazards and immediate concerns for the product.
Requirements for ventilation to maintain safe working environment.
Recommendations for using protective gloves.
Compliance information for U.S. federal laws and regulations.
General| Input Voltage | 24 V DC |
|---|---|
| Protection Class | IP20 |
| Power Supply | 24 V DC |
| Mounting | DIN Rail |
| Series | ET 400 Series |
| Application | Industrial Automation |
To Next Page