Etherma LAVA BATH 2.0 - Page 12

HEATING MODE
The infrared heating has a very large radiation component
and a very small convective component of the heating power.
For reasons of safety, the surface temperature is max.
80 °C,
therefore
LAVA
®
BATH suits ideally as zone heating and thanks
to the included towel holder as towel heater as well.
The infrared heating by ETHERMA mainly heats solid objects
and, only to a lesser extent, directly heats the room air. There-
fore, these devices are ideal for additional temperature control.
Depending on the size of the device, the infrared heating re-
quires a certain time until the operating temperature is
reached. Only then the radiation can take its full effect.
The glass panel produced for the product consists of 6 mm
single-pane safety glass (ESG). This is much more resistant
in contrast to conventional glasses and is designed for signif-
icantly higher impact forces. Nevertheless, you should avoid
excessive stress. In case of damage, ESG shatters into many
small parts with blunt edges, so that the risk of injury is min-
imized. When choosing the place of installation, please note
that a negligible amount of tempered glass still causes a so-
called "spontaneous breakage", which means that the glass
shatters even without external inuence. Therefore, choose
the installation location of the device in such a way that even in
these cases no danger to persons or objects is to be expected.
MAINTENANCE AND CARE
The infrared heating is designed so that it gives off its heat via
the surface in the form of radiation. The device does not con-
tain any parts requiring special maintenance. In order to ser-
vice your infrared heater, we recommend using a damp cloth.
Please do not use any scouring agents, since they may leave
scratch marks on the surface.
USER MANUAL
ATTENTION: When you want to clean the infrared
heating, the heating device must be cold!
TECHNICAL DATA LAVA
®
BATH 2.0
> Voltage: 230 V
> Output: 350 – 700 W
> Surface temperature: max. 80 °C
> Surface: Steel sheet, 6 mm ESG safety
glass, 6 mm ne stone, 6 mm
Corian
> Device/Installation depth: Steel sheet 26/57 mm, glass
& ne stone 30/61 mm, Corian
36/67 mm
> IP Rating: IP X4
> Connection cable: 1 m, with plug
> Warranty: 5 years
LAVA
®
BATH 2.0 STEEL infrared heating, steel, white (W)
Type Art.No. Output (W) Length (mm) Hight (mm) Weight (kg)
Halti
LAVABATH2-ST-350-W 40560 350 900 630 10 max. 1
LAVABATH2-ST-500-W 40562 500 1300 630 14,5 max. 3
LAVABATH2-ST-700-W 40564 700 1600 630 18 max. 3
LAVA
®
BATH 2.0 GLAS infrared heating, glass, purewhite (PW)
Type Art.No. Output (W) Length (mm) Hight (mm) Weight (kg)
Halti
LAVABATH2-GL-350-PW 38126 350 900 630 14
max. 1
LAVABATH2-GL-400-PW 38082 400 1300 500 16 max. 3
LAVABATH2-GL-500-PW 35909 500 1300 630 20 max. 3
LAVABATH2-GL-600-PW 38087 500 1600 500 20 max. 3
LAVABATH2-GL-700-PW 35914 700 1600 630 25 max. 3
LAVA
®
BATH 2.0 GLAS infrared heating, glass, mirror (MR)
Type Art.No. Output (W) Length (mm) Hight (mm) Weight (kg)
Halti
LAVABATH2-GL-350-MR 35908 350 900 630 14
max. 1
LAVABATH2-GL-400-MR 38086 400 1300 500 16 max. 3
LAVABATH2-GL-500-MR 35913 500 1300 630 20 max. 3
LAVABATH2-GL-600-MR 38091 500 1600 500 20 max. 3
LAVABATH2-GL-700-MR 35918 700 1600 630 25 max. 3
LAVA
®
BATH 2.0 STONE infrared heating, ne stone, structural grey (G)
Type Art. no. Output (W)
Length (mm) Height (mm)
Weight (kg) Halti
LAVABATH2-S-350-G 40915 350 900 630 14 max. 1
LAVABATH2-S-400-G 40916 400 1300 500 16 max. 3
LAVABATH2-S-500-G 40917 500 1300 630 20 max. 3
LAVA
®
BATH 2.0 CORIAN infrared heating, Corian, pure white (PW)
Type Art. no. Output (W)
Length (mm) Height (mm)
Weight (kg) Halti
LAVABATH2-CO-350-PW 40897 350 900 630 14 max. 1
LAVABATH2-CO-400-PW 40898 400 1300 500 16 max. 3
LAVABATH2-CO-500-PW 40899 500 1300 630 20 max. 3
12