How to fix F10 error on ETNA VW244N Dishwasher?
If the ETNA Dishwasher shows error code F10, it indicates overfilling water. Try unblocking the drainage pump, referring to the Care and cleaning chapter.
Why my ETNA Dishwasher does not start?
If your ETNA Dishwasher isn't starting, there could be several reasons: * Make sure you've pressed the start button, as the display should start counting down. * Ensure the door is properly closed. * If you opened the dishwasher mid-cycle to add dishes, close the door and wait for the program to resume. * Check that the door lock clicks into place; if not, open the door, press and hold the start button until the display counts down, wait for it to end, then close the door again. * Verify if the Delayed start option is activated and cancel it by pressing and holding the start button for three seconds if needed. * Confirm that the dishwasher is properly plugged into the wall socket and that the fuse/circuit breaker hasn't tripped.
How to fix dishes not drying in ETNA VW244N?
If your ETNA Dishwasher leaves dishes not dry enough, first, activate the Automatic door opening setting. Next, make sure you fully load the dishwasher. Check the rinse aid level and increase the dosage if it is set too low. If you're using all-in-one detergent with the TAB setting activated, try switching to separate detergents, top up with salt and rinse aid, or deactivate the TAB setting.
What to do if water remains in my ETNA VW244N?
If water remains in your ETNA Dishwasher, it might be due to several reasons. Check if the filter is clogged and clean it. Ensure the filter is correctly fitted. Inspect the drainage pump for debris and clean it. Verify the yellow drainage pump stop is in place. Make sure the drainage hose isn't kinked or blocked. If blocked, disconnect the drainage hose from the sink unit's water trap and clear any debris, ensuring the connection has an inner diameter of at least 14 mm.
How to get rid of bad odour in ETNA VW244N?
If there's a bad odor in your ETNA Dishwasher, it could be due to dirt around the seals and in corners. Clean these areas with a washing-up brush and a low-foaming cleaner. Also, running low-temperature programs for extended periods can cause odors. To resolve this, run a high-temperature program once or twice a month, or use a self-cleaning program.
How to remove grease deposits in ETNA Dishwasher?
If there are grease deposits in your ETNA Dishwasher, it's likely because low-temperature programs have been used for a long time. Try selecting a high-temperature program like Intensive 70° to dissolve the grease on very dirty dishes, or run a self-cleaning program.
How to fix F67 error on ETNA Dishwasher?
If the ETNA Dishwasher shows error code F67, there is a water inlet fault. First, check that the water tap is turned on. Then, inspect the outer filter on the inlet hose to ensure it's not blocked, consulting the Unblocking the inlet hose filter section in the Care and cleaning chapter.
Why are there spots on stainless steel or silver in my ETNA VW244N?
If you're finding spots on stainless steel or silver items after using your ETNA Dishwasher, it could be due to a few reasons. Certain foods like mustard, mayonnaise, lemon, vinegar, salt, and dressings can cause spots if left on items for too long, so rinse these off before washing. Also, different metals like stainless steel and aluminum can cause spots on silver if they touch during washing, so separate them. Check your rinse aid dosage setting and adjust as needed. If you're using all-in-one detergent with the TAB setting activated but aren't getting good drying results, try switching detergents or deactivating the TAB setting and using salt and separate rinse aid. Ensure your salt compartment is full and that your water softener setting is correct. Finally, check that the salt compart...
What to do if I cannot close the door of my ETNA VW244N?
If you cannot close the door of your ETNA Dishwasher, check that the baskets are correctly positioned horizontally. Also, make sure that the dishes are not blocking the baskets from sliding properly into place.
Why are there spots left after washing in my ETNA Dishwasher?
If you're finding spots left after washing in your ETNA Dishwasher, it could be due to lipstick or tea/coffee stains, which are often difficult to remove. Try using a detergent that contains a bleaching agent to help remove these stubborn stains.
General| Type | Freestanding |
|---|---|
| Color | White |
| Number of programs | 6 |
| Number of place settings | 12 |
| Place settings | 12 |
| Programs | Eco, Intensive, Normal, Glass |
| Dimensions (HxWxD) | 845 x 598 x 600 mm |
To Next Page
