VEHICLE ALARM SYSTEM 'EUROSEC E50'
User Manual
'EUROSEC E50' is up - to - date vehicle alarm system designed for users looking for quality and appreciating their time. System
generates secure variable code and functions in conformity to requirements of EU Directives. 'EUROSEC E50' is distinguished not
only by the reliable engine immobilization preventing vehicle theft but also by possibility of turning the alarm OFF by means of
adjustable PIN code. This is extremely handy when facing remote control loss for example during some travel or when the remote
control battery is low.
1. SYSTEM UNIT.
System unit performs main security functions, thus it is extremely important to hide it well in the passenger compartment of a
vehicle. After the installation of the system unit all system settings and pre-programming of the new remote controls is done by using
the PIN code. Manufacturer supplies alarm system with default 4 - digit PIN code (Fig. 1) that can be found on the Identification
label of alarm system (Fig. 2). Afterwards the user should change it into some other easy memorable 4 - digit number. It is
recommended to write down the new PIN code, however do not keep this information in your vehicle. In addition, do not use your
birthday date or home address for the PIN code.
2. REMOTE CONTROL.
The system comes with 2 remote controls (radio transmitters) (Fig. 3 and Fig. 4) though it is possible to program up to 5 remote
controls (see section 6.4.). It is recommended to replace remote control battery after every 12 months. All types of 23A batteries
(12V) are eligible for use. Though remote control casing ensures protection of inside electronics from moisture, dipping of remote
control device into water is not allowed under any circumstances.
3. ALARM ARMING USING REMOTE CONTROL BUTTON .
3.1. ALARM ARMING. Shortly press remote control button . Vehicle direction indicators flash once, system LED starts flashing
in short bursts of light. Security alarm is turned ON. If vehicle incorporates central lock, the doors are locked.
3.2. ARMING WITH NO SENSOR. In case the system is connected with single-level sensor, press and hold button . Direction
indicators will flash once, after 2 seconds direction indicators will shortly go on once more. Release the button. Protection is ON,
however the sensor detecting vehicle body vibrations or movements inside the passenger compartment is deactivated and does not
trigger the alarm system. Vehicle doors, luggage compartment and engine hood are secured! If the system is connected with two-level
sensor and you want to turn on the security without triggering sensor warning signal, press and hold button . The direction
indicators will flash once, after 2 seconds the direction indicators will go ON. Release the button. If you wish to turn the arming ON
without a sensor - press and hold the button . Vehicle direction indicators flash once, after 2 seconds direction indicators will
shortly go on once more. Release the button only with direction indicators in the off position.
3.3. ALARM INTERRUPT. System alarm starts generating noise (warning) in case of vehicle door, engine bonnet or luggage
compartment opening, body movement or passenger compartment break-in when alarm is operational. Press remote control button or
to terminate alarming yet the security system remaining operational. If you want to turn OFF the response to vibration or volume
sensor till the next rearming, perform actions in section 3.2.
3.4. CLOSING WINDOWS AND SUNROOF ON ARMING. Installation of 'EUROSEC E50' enables system setting in a way the
system generates a 40 second pulse designed for closing of windows and sunroof. In case of holding any of the buttons during
impulse generation, the latter will be discontinued.
3.5. CENTRAL LOCK CONTROL WITH ENGINE OPERATIONAL. If doors of the vehicle are closed and the engine is ON,
doors are locked with first press of button and unlocked with the second press. Very handy when travelling with children or
heating vehicle.
3.6. AUTOMATIC DOOR LOCKING ON START UP OF THE ENGINE. The driver will definitely feel safer if the doors are
locked automatically on the start of the engine. After turn OFF of the engine the doors are unlocked. To turn automatic door lock
ON or OFF disarm the system or turn OFF the engine, simultaneously press and buttons and hold them till a short alarm
signal.
3.7. CHECKING WHETHER THE SYSTEM IS ON. Press remote control button . If the system is armed, vehicle direction
indicators flash once.
3.8. VEHICLE LOCATOR, PANIC AND EMERGENCY CALL FUNCTION. If the system is armed, press and hold remote
control button . Direction indicators flash once, 1.5 seconds afterwards the siren starts sounding. The function can be used for
locating your vehicle in a big parking lot, for warning nosy parkers, or attracting attention of by passers in case of emergency.
Disarming
Device control
Fig. 1 The PIN code.
Garage control
Alarm interrupt
Sensors deactivation
Central lock control
Arming verification
Emergency control
Arming
Label
PIN code
Fig. 2 The Identification label.
Fig. 4 Three - button remote control
Alarm interrupt
Sensors deactivation
Central lock control
Arming verification
Emergency call
Arming
Disarming
Engine immobilization OFF
Device control
Fig. 3 Two - button remote control
To Next Page
Need help?
General