Need help?Do you have a question about the Evolution R255 SMS and is the answer not in the manual?
General| Cutting Width | 255mm |
|---|---|
| Motor Power | 1600 W |
| Blade diameter | 255 mm |
| Max cutting depth at 90° | 80 mm |
| Max cutting depth at 45° | 55 mm |
| Voltage | 230 V |
| Frequency | 50 Hz |
Read operating and safety instructions carefully and completely for safe use.
Complete product registration online to validate warranty for prompt service.
Explains all safety labels and symbols found on the machine and in the manual.
Defines the proper application and use of the multi-material sliding mitre saw.
Outlines uses and modifications that are forbidden for this power tool.
Caution for persons with reduced physical, sensory, or mental capabilities.
Guidelines for safe electrical operation, including RCD use and cord care.
Precautions for using the tool outdoors, emphasizing weather and dampness.
Essential safety advice to reduce risks of fire, electric shock, and injury.
Safety measures related to keeping the work area clean, lit, and free from hazards.
Further electrical safety advice, including plug matching and avoiding grounded surfaces.
Advice on staying alert, using PPE, and preventing unintentional starting.
Instructions on proper tool usage, maintenance, and keeping cutting tools sharp.
Guidelines for servicing the power tool with genuine replacement parts.
Safety precautions unique to the operation of mitre saws.
Guidelines on clamping, supporting, and handling workpieces to prevent accidents.
Ensuring proper clearance for workpieces and avoiding contact with the spinning blade.
Safe methods for cutting, including workpiece stability and preventing kickback.
Critical warnings about rotating saw blades and safe handling practices.
Recommendations for wearing PPE like hearing, eye, and respiratory protection.
Warnings regarding lead paint and dust hazards from certain materials.
Caution about dust produced from materials like MDF and recommended protection.
Ensures correct blade selection, machine stability, and guard functionality.
Guidance on securing workpieces and planning cuts for safe execution.
Emphasizes wearing eye protection to prevent severe eye damage from debris.
Safety advice for carrying the mitre saw to prevent back injury.
Safe methods for lifting and transporting the heavy mitre saw.
Instructions for unpacking, checking machine condition, and handling packaging.
Lists optional accessories available for purchase from Evolution.
Lists necessary tools for assembly and adjustments, noting which are supplied.
Identifies the main parts to be assembled and fitted to the machine.
Instructions for fitting the Mitre Locking Knob.
Guidance on adjusting the bevel neck to the 0° position.
Steps to reset locating lugs if they have been accidentally 'tripped'.
How to correctly align and attach the cutting head to the carriage arms.
Instructions for fitting the slide rail cover onto the cutting head.
Guidance on fitting the two handed table extension pieces.
Proper method for routing and securing the machine's power cable.
Steps to release and raise the cutting head to its upper position.
Safe procedures for installing or removing the saw blade.
How to check and reset precision angles like bevel and mitre.
Detailed steps to adjust and set the 0° and 45° bevel stops accurately.
How to align the bevel pointer with the 0° mark on the scale.
Steps to adjust and set the 45° bevel stop accurately.
How to align the machine fence square to the blade.
Repositioning the mitre angle pointer for accurate readings.
How to use the depth stop to limit cutting depth for slots or trenching.
Adjusting the sliding upper fence section for clearance during cuts.
Information on the laser guide for previewing the cut path.
Crucial safety rules for using the laser guide, avoiding eye hazards.
How to use the laser guide for known and unknown cutting angles.
Procedure to check and adjust laser alignment with the blade marks.
Lists warning labels found on the machine, including laser radiation.
Instructions for securely mounting the saw to a workbench or stand.
Advice on mounting the saw for portable use on a plywood board.
How to use the hold down clamp for securing workpieces.
Safe hand and body placement to avoid the 'no hands zone' and blade path.
Operation of the trigger switch for starting and stopping the motor.
Steps to prepare for a cut, including good footing and workpiece security.
Method for performing chop cuts with the sliding carriage locked.
How to perform slide cuts using the sliding carriage system.
Adjusting the rotary table for mitre cuts using positive stops.
How to tilt the cutting head for bevel cuts, including 33.9° stop.
Performing combined mitre and bevel cuts simultaneously.
Configuring the machine for cutting crown moulding angles.
Proper positioning and cutting method for bowed workpieces.
Steps to safely clear jammed material and inspect the machine.
Details on fitting optional accessories like the dust bag and extraction adapter.
Checklist to ensure all parts are correctly assembled before use.
Procedures to verify the machine's safety and operational integrity.
Routine checks, cleaning, and warnings regarding motor cleaning.
Guidance on proper disposal of waste electrical products for recycling.
To Next Page
