Extreme Max Boat Lift Buddy User Manual

Customer Service: 651-357-1874 | boatliftboss@extrememax.com | www.extrememax.com
3006.4550 - 12 Volt
3006.4553 - 120 Volt
Boat Lift Buddy™
Installation & Use Instructions
If there are any missing or damaged parts,
DO NOT return Boat Lift Buddy™ to the retailer.
Call the Boat Lift Buddy™ Service Dept. at: 651-357-1862
E-mail - service@extrememax.com
2540ex0116
Tools Required:
• 3/8” Socket or Wrench
• 7/16” Socket or Wrench
• 9/16” Socket or Wrench
• 15/16” Socket or Wrench
• Adjustable Wrench
• Flat Screw Driver
• 3/16” Drill Bit (Optional)
Components List:
(1) Torque Arm
(1) Off-Set Bracket
(1) Mounting Bracket
(4) 1/4” Bolts
(4) Self Tapping Screws
(2) Spacer Bars
(1) Bungee Cord
(2) Hose Clamps
(1) 15’ Battery Cable
(1) Motor Assembly
(1) 5/8” x 1-1/2” Bolt
(1) 5/8” Locking Nut
(4) 3/8” Bolts
Warning for 12-Volt Models:
In case of emergency, pull apart the red quick connectors to shutdown the system.
*View an installation demonstration on the Extreme Max Products
YouTube channel at: www.youtube.com/extrememaxproducts
Warning for 120-Volt Models:
All 120 Volt Boat Lift Buddy
™
units must only be used on an electrical circuit which has ground fault interrupter protection. The
interrupter and its supply circuit MUST be installed to local and state electrical codes. The supply circuit needs to be properly
sized for the correct length of run and requirements. In low voltage situations a buck boost transformer can be used to increase
voltage. Contact a licensed electrical contractor for correct installation. Failure to wire properly and or install ground fault
interrupter puts user at high risk of injury or death.
Unplug Boat Lift Buddy
™
when not in use or before storms to help prevent electrical damage from lightning or power surges.

Extreme Max Boat Lift Buddy Specifications

General

Brand	Extreme Max
Model	Boat Lift Buddy
Category	Lifting Systems
Language	English

Summary

Safety Warnings

Warning for 12-Volt Models

Emergency shutdown procedure for 12-volt models by pulling red quick connectors.

Warning for 120-Volt Models

Mandatory GFCI protection and proper circuit sizing for 120-volt models to prevent shock.

Assembly Instructions

Assemble the Torque Arm

Steps to assemble the torque arm using bolts and wrenches.

Attach the Motor Assembly

Instructions for attaching the motor assembly to the torque arm.

Assemble the Offset Bracket

Steps to assemble the offset bracket with a spacer bar and bolts.

Mounting Bracket Installation

Assemble the Mounting Bracket

Steps to assemble the mounting bracket with a spacer bar and bolts.

Bracket Placement

Guidance on positioning mounting and offset brackets relative to the lift wheel.

Motor and Bracket Positioning

Position the Motor Assembly

Guidance on positioning the motor assembly, recommending the 10 o'clock position.

Attach the Mounting Bracket

Two options for attaching the mounting bracket: self-tapping screws or hose clamps.

Finalizing Installation

Secure Torque Arm

Instructions for securing the torque arm using the offset bracket.

Secure Motor Assembly

Procedure for securing the motor assembly to the lift wheel.

Check Alignment

Ensuring the torque arm is parallel to the drive wheel.

Attach the Bungee Cord

Attaching the bungee cord for proper tension and function.

Operation and Accessories

Safety & Use Instructions

General safety guidelines and recommendations for operating the Boat Lift Buddy.

Available Accessories

List of optional accessories for the Boat Lift Buddy system.