EasyManua.ls Logo

EYEZONE P102-5m - User Manual

Default Icon
10 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
EYEZONE P102-5m
User Manual
O c t 2 6 , 0 7
F 3 4 4 1 2 F 0 7
FCC Notices
It’s herewith confirmed to comply with the requirements of FCC Part 15 Rules. Operation is subject
to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a residential installation.
This equipment generated uses and can radiate radio frequency energy and if not installed and used
in accordance with the instruction manual may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio of television reception, which can be determined
by turning the equipment off or on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio TV technician for help.
CE Declaration
This device complies with CE class B.
*EN55013
EN61000-3-2
EN61000-3-3
EN55020
Printed in Taiwan R.O.C.
All contents are subject to change without notice.
All trademarks are the property of their respective owner.

Table of Contents

Questions and Answers

  • T
    Thomas OrtizAug 11, 2025
    How to fix no picture on EYEZONE Digital Signage?
    • R
      Robert HarveyAug 11, 2025
      If your EYEZONE Digital Signage isn't displaying a picture, start by checking that the power supply is properly connected. Additionally, ensure that the P102-5m is turned on.
  • R
    rarnoldAug 17, 2025
    What to do if there is no sound on my EYEZONE Digital Signage?
    • S
      snorrisAug 17, 2025
      If you're not getting any sound from your EYEZONE Digital Signage, first ensure that the mute function isn't activated. Also, verify that the volume is turned up to an audible level.
  • R
    Roberto MillerAug 25, 2025
    Why is my EYEZONE P102-5m Digital Signage remote control not working?
    • P
      pamelamontgomeryAug 25, 2025
      If your EYEZONE Digital Signage remote control isn't responding, first ensure there's a clear line of sight between the remote and the device. If that doesn't work, try replacing the batteries in the remote control.
  • J
    Julia BridgesAug 29, 2025
    What to do if my EYEZONE Digital Signage is not reading the memory card?
    • P
      perrymatthewAug 29, 2025
      For memory card issues with your EYEZONE Digital Signage: * Gently and securely push the cards in. * If a card doesn't insert easily, check its direction. * Confirm the card's format. The P102-5m supports CF, SD, MMC, and MS (Pro) memory cards.
  • E
    Erik GriffinSep 5, 2025
    How to correct timer inaccuracy on EYEZONE Digital Signage?
    • K
      Kevin FoxSep 5, 2025
      To address timer inaccuracy on your EYEZONE Digital Signage timer function: first, press the “EDIT” key to open the timer setup window and confirm that the time is correct. Also, if using the “Timer Function”, it is suggested to check whether the time is correct every three months.

EYEZONE P102-5m Specifications

General IconGeneral
Resolution1920 x 1080
Brightness500 cd/m²
Contrast Ratio1200:1
Response Time6 ms
Viewing Angle178°/178°
Power Consumption150W (Typical)
Operating Temperature0°C to 50°C
Storage Temperature-20°C to 60°C
Display Size55 inches
Input Voltage100-240V AC