EasyManua.ls Logo

EZPOLE CLASSIC User Manual

EZPOLE CLASSIC
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Instructions for the CLASSIC Sectional Flagpole
Tools & Material Needed:
l Post Hole Digger/Shovel
l Level
l Tape Measure
l Mixing Container
l 80 lbs. + of Quick Setting Cement
l Approximately 3” of Gravel
Flagpole Kit Includes:
l Aluminum Ground Sleeve
l Aluminum Gold Ball
l 3 to 5 Aluminum Flagpole Sections
(Depending on Size—13’ 3 sections, 17’ 4 sections, 21’ 5 sections)
l Truck Top installed to Top Section and pre-strung with
rope
l Section with installed Cleat
l 3’ x 5’ Nylon Sewn USA Flag
(*Note not all vendors add ag)
l Clip Pack: 4 nylon clips and ag etiquette leaet
l Manufacturer Product Warranty Registration
(Must be Returned within 90 Days of Purchase or
Warranty is Void)
See back for assembly instructions including how to y at half-mast.
STEP 1: Select agpole location. Call 811 before you dig. Check for
underground sprinklers, water and electrical lines. Make sure your ag
has clearance to y in all directions. Are you too close to the house?
Watch the roof!
STEP 2: Dig a hole approximately 26” deep by 12-18” in diameter (26”L x
12-18”W).
STEP 3: Place approximately 3” of gravel in hole to allow for drainage.
STEP 4: Place aluminum ground sleeve into gravel – to prevent concrete
from owing inside.
STEP 5: Mix cement and pour around ground sleeve. Repeat until hole is
lled (the more cement the better). It is OK to have your ground sleeve
an inch or two above ground level. Can be lled in with mulch, dirt and/
or ower bed.
STEP 6: Carefully insert pole section swedge end up into ground sleeve
as cement will be wet . Use a level to make sure pole is straight. Remove
pole section after level, concrete must cure for at least 24 hours.
STEP 7: Assemble your agpole. Flip over for proper assembly
instructions.
STEP 8: Insert agpole into ground sleeve! Enjoy!
Manufacturer suggests taking agpole down during high winds and strong storms also
storing agpole during winter for those in aected regions.
FOR PARTS AND SERVICE:
EZPOLE FLAGPOLES/ 1489 EAST 363RD STREET/ EASTLAKE, OHIO 44095
TOLL FREE: 888-454-9164/ LOCAL: 440-951-1011/ FAX: 440-951-2933/ www.ezpole.com
26”
12-18”
In Ground
Sleeve
Gravel
6-8”
3”
Concrete
Question and Answer IconNeed help?

Do you have a question about the EZPOLE CLASSIC and is the answer not in the manual?

EZPOLE CLASSIC Specifications

General IconGeneral
BrandEZPOLE
ModelCLASSIC
CategoryRacks & Stands
LanguageEnglish

Summary

Installation Steps

Select Flagpole Location

Choose a location and check for underground utilities before digging.

Dig Installation Hole

Dig a hole approximately 26" deep by 12-18" in diameter.

Add Gravel for Drainage

Place approximately 3" of gravel in the hole to ensure proper drainage.

Place Ground Sleeve

Insert aluminum ground sleeve into gravel to prevent concrete flow.

Pour Cement Around Sleeve

Mix and pour cement around the ground sleeve, ensuring it is filled.

Insert Pole Section

Carefully insert pole section into the sleeve while cement is wet, using a level.

Assemble Flagpole Sections

Flip over for proper assembly instructions for all flagpole sections.

Final Insertion and Enjoy

Insert flagpole into the ground sleeve and enjoy the assembled flagpole.

Flagpole Assembly and Usage

Pole Assembly Order

Details the correct order for assembling flagpole sections from bottom to top.

Attaching Nylon Clips to Halyard

Instructions on how to attach nylon clips to the flagpole halyard rope.

Flying Flag at Half-Mast

Guidance on how to properly fly the flag at half-mast.