Smoke Alarm User’s Manual
Please read and save this manual
Photoelectric smoke alarms
are generally more effective
at detecting slow burning fires
which smoulder for hours
before bursting into flame.
eg. cigarettes burning in couches
or bedding.
MAIN FEATURES
DC operated photoelectric type smoke alarm
Photoelectric sensor for slow smouldering
fires
Insect proof
Self-Test button
Environmentally friendly non-radioactive technology
High and stable sensitivity
Quick
fix mounting bracket for easy installation
Fitting and battery tamper-resist feature
LED operation indicator
Extra loud alarm sound over 8
5
dB
Low-battery and battery missing warning indicator
Auto-reset when smoke clears
SPECIFICATION
Model Number: FFP
9
VH
Detection Type: Photoelectric Chamber
Power Source:
9
V DC Battery
Standby Current: 1
5
uA max
Alarm Current:
3
0mA max
Alarm Sound Level 8
5
Decibels at
3
meters
Operation Temperature:
5
º
C to
45
º
C
Ambient Humidity: 10%-
9
0%
Sensitivity to Smoke:
3
.0-6.0 %Obs /m
Compact size: 110mm diameter
IMPORTANT SAFETY INFORMATION
1 .This smoke alarm requires constant working
9
-volt
battery to operate properly. This smoke alarm WILL
NOT work if DC power is not connected or has failed
or been interrupted for any reason, the battery
is removed, drained or improperly connected. DO NOT
use any other kind of battery except as specified.
DO NOT connect this smoke alarm to any other type
of smoke alarm or auxiliary device, except those
listed in this manual.
2.
The Test button accurately
PHOTOELECTRIC SMOKE ALARM MODEL: FFP
9
VH
Hush button
tests all smoke alarm functions. Do not use any
other test method. Test
smoke alarm weekly to
3
.DO NOT remove or disconnect battery to silence
unwanted alarms. This will remove your protection.
Open windows or ventilate the smoke alarm to
silence it.
4
. This smoke alarm may be installed by a licensed,
qualified electrician. Observe and follow all
local and national electrical and building codes
for installation.
5
.
6
. Install a smoke alarm in every room and on every
level of the home. Smoke may not reach the smoke
alarm for many reasons. For example, if a fire starts
in a remote part of the home, on another level, in a
chimney, wall, roof, or on the other side of a closed
door, smoke may not reach the smoke alarm in time
to alert household members. A smoke alarm will not
promptly detect a fire except in the area or room in
which it is installed.
7
8. Smoke alarms can only sound their alarms when
they detect smoke. Smoke alarms detect combustion
particles in the air. They do not sense heat, flame
or gas. This smoke alarm is designed to give audible
warning of a developing fire. However, many fires
are fast-burning, explosive, or intentional. Others are
caused by carelessness or safety hazards.
Smoke may not reach the smoke alarm QUICKLY
ENOUGH to ensure safe escape.
9
. Smoke alarms have limitations. This smoke alarm
is not foolproof and is not warranted to protect lives
or property from fire. Smoke alarms are not a
substitute for insurance. Homeowners and renters
should
insure their lives and property. In addition,
reason, you must test the smoke alarm
Note:
For best protection, we recommend that you
install
ensure proper operation.
it is possible for the smoke alarm to fail at any time.
For this
weekly and replace it every 10 years.
a smoke alarm in every room.
BEDROOM
HALL
BEDROOM
LIVING ROOM
KITCHEN
BASEMENT
MULTI-STORY RESIDENCE
SMOKE ALARM PLACEMENT
Typical single-story home
Typical Multi-story or split level home
DINING ROOM
LIVING ROOM
BEDROOM
BEDROOM
KITCHEN
SINGLE-STORY RESIDENCE, APARTMENT, MOBILE HOME
KEY:
Minimum required smoke alarm locations
Recommended additional smoke alarm locations
Smoke alarms with hush features recommended
for additional protection
IMPORTANT SMOKE ALARM PLACEMENT
AND EXCEPTION INFORMATION
1. Place as close to the centre of the ceiling as possible or
at least no closer than
3
00mm to any wall or corner.
2. Install a minimum of two smoke alarms in every
home, no matter how small the home.
3. Install a smoke alarm in each room that is divided
by a partial wall.
4. Install a smoke alarm in lived-in attics or attics
which house electrical equipment like furnaces, air
conditioners, or heaters.
HOW TO INSTALL THIS SMOKE ALARM
WARNING:
Smoke alarm installation must be in
accordance with the requirements of the
national electrical code and any local
codes that may apply.
1. Remove the mounting plate by turning counterclockwise
at the back of the smoke alarm.
(To later engage tamper-resist
feature, twist out and
set aside one of the pins
moulded into plate. Both
pins are exactly the same.)
2. Install the mounting plate to ceiling or wall with
mounting screws.
3. Lift open battery pocket door.
4. Connect new 9-volt battery to
battery connector inside
securely connected.
battery pocket. Be sure battery is
Red LED may blink briefly when battery is installed.
300mm
Heat and
smoke
from fire
Best here
Dead air space, Do Not install here
Dead air space,
Do Not install here
300mm
minimum
900mm min
Install a smoke alarm on the ceiling or wall inside each
bedroom and in the hallway outside each separate
sleeping area. If a bedroom area hallway is more than
9 metres (30 ft) long, install a smoke alarm at each
end.
If there is a basement: Install a smoke alarm on the
basement ceiling at the bottom of the stairwell.
Install a smoke alarm on the ceiling or wall inside each
bedroom and in the hallway outside each separate
sleeping area. If a bedroom area hallway is more than
9 metres (30 ft) long, install a smoke alarm at each
end. Please install a smoke alarm on the top of a
first-to-second floor stairwell.
This smoke alarm is designed to be used inside a single
unit dwelling only. In buildings with several dwellings,
each individual living unit should have its own smoke
alarms.
Do not install in non-residential buildings.
This smoke alarm is not a substitute for a complete
alarm system.
WARNING:
Incorrect orientation will result in a
decrease in operational effectiveness.
DO NOT INSTALL SMOKE ALARMS NEAR:
1. Areas near appliances or where normal combustion
regularly occurs (near furnaces, hot water heaters).
Use a specialised smoke alarm with unwanted alarm
control for these areas.
2. Areas with high humidity, like bathrooms,
near dishwashers or washing machines. Install at
least
3
metres (10 Feet) away from these areas.
3
. Air returns or heating and cooling supply vents.
Install at least
9
00mm (
3
Feet) away from these areas.
The air could blow smoke away from the detector,
4
. Rooms where temperatures may fall below
5
º
C
5
. Extremely dusty, dirty, or insect-infested areas
where loose particles interfere with smoke alarm
operation.
or rise above
45
º
C
interrupting its alarm.
. Smoke alarms may not alert every household
member every time. The alarm sound is loud in
order to alert individuals to a potential danger.
However, there may be limiting circumstances
where a household member may not hear the alarm
(i.e. outdoor or indoor noise, sound sleepers, drug or
alcohol usage, hard of hearing, etc.). If you
suspect that this smoke alarm may not alert
household members, install and maintain specialty
smoke alarms.
Household members must hear the alarm’s warning
sound and respond, to quickly reduce the risk of
damage, injury or death that may result from fire.
If a household member is hearing impaired, install
special smoke alarms with lights or vibrating devices
to alert occupants.
To Next Page
General
