What to do if Famsun Muyang SJPS215 products look rough with uneven lengths?
If the products appear rough with uneven lengths, the issue might stem from poor conditioning, blocked die plate holes, coarse ground particle size or bad die plate quality. Try the following: * Enhance material conditioning. * Stop production and clean the die plate. * Improve grinding for finer particles. * Use a die plate made by a reputable manufacturer.
Why is the temperature of conditioning failing to meet the requirement in Famsun Industrial Equipment?
If the conditioning temperature isn't meeting requirements, it could be due to insufficient steam pressure or a blocked steam pipeline. Check the steam pressure and adjust it to the normal 4bar. Also, clean the steam pipelines.
What to do if Famsun Muyang SJPS215 Industrial Equipment material cannot be discharged suddenly during normal operation?
If material discharge stops suddenly during normal operation, the cause may be excessive feeding in a short period, feeding cut-off, or blocked die holes. To resolve this, stop production to check and correct the feeding issue or clear any blockage in the die holes.
How to fix insufficient expansion in Famsun Industrial Equipment?
Insufficient expansion can occur due to insufficient gelatinization. You can try the following to fix it: * Increase feeding. * Raise the conditioning temperature. * Raise the jacket heating temperature. * Increase the rotary speed of main motor.
Why is the temperature of the extruder barrel not reaching the required temperature in Famsun Industrial Equipment?
If the extruder barrel isn't reaching the required temperature, it could be due to low steam conditioning temperature, a blocked steam pipeline in the jacket, or a blocked steam pipeline in the extruder barrel. To fix this: * Raise the conditioning temperature to make the material temperature 80?-90? after conditioning. * Clean the steam pipeline of the jacket. * Clean the steam pipeline into the extruder barrel.
What causes poor product forming in Famsun Industrial Equipment, and how to resolve it?
Poor product forming can result from several factors. These include an improper raw material formula, processing temperature being too high or low, unstable feeding, product moisture content being too high or low, incorrect cutting speed, a worn-out blade, or ground particles that are too coarse. Suggested solutions include: * Changing the raw material formula. * Reconfiguring the components in machine barrels. * Adjusting to even feeding. * Reducing or increasing water or steam addition. * Adjusting the rotating speed appropriately. * Replacing the blade. * Grinding the raw materials to obtain the defined granularity.
How to fix throughput decrease in Famsun Muyang SJPS215 Industrial Equipment?
A decrease in throughput may be caused by a worn-out pressure ring, wear ring, or a seriously worn-out screw head. To address this, replace the wear ring or pressure ring, or replace the screw head.
What causes excessive expansion in Famsun Industrial Equipment, and how can it be corrected?
Excessive expansion is caused by excessive temperature. To correct this, decrease the temperature.
What causes uneven intermittent discharge in Famsun Industrial Equipment?
Uneven intermittent discharge is caused by a low filling degree of extruder barrels. To resolve this, increase feeding.
What causes product length to be too long or too short in Famsun Industrial Equipment?
If the product length is either too long or too short, it is caused by the cutter speed being too low or too high. Adjust the cutting transmission speed to correct it.
Conditions for safe operation, including temperature, humidity, and altitude.
Classification and meaning of safety warning signs for equipment operation.
Details on safety signs posted on equipment for personal safety.
Operator responsibilities, training requirements, and adherence to regulations.
Procedures for safe handling and installation of the equipment.
Guidelines for safe operation, inspection, and maintenance procedures.
Requirements for personal protective equipment and safety practices during operation.
Precautions against dust explosion and fire hazards for safe production.
Measures for environmental protection and machine disposal at end-of-life.
Uses and capabilities of the SJPS215 Single-Screw Extruder in the aquafeed industry.
Overview of the extruder system's components and its operational process.
Detailed description of individual equipment parts like feeding bin and feeder.
Procedures and diagrams for safely lifting extruder components.
Recommendations for packaging and handling during shipment.
Procedures for checking equipment upon arrival and storing it properly.
Steps for installing the extruder, including foundation and bolting.
Details on model description and basic specifications of the extruder.
Key technical specifications including power, speed, and dimensions.
Conditions for material grinding, environment, and configuration.
General| Brand | Famsun |
|---|---|
| Model | Muyang SJPS215 |
| Category | Industrial Equipment |
| Language | English |
To Next Page