FBII Omni-KP User Manual

K3590-FBIIV1 6/01
REMOTE KEYPADS
Omni
®
-KP & Omni
®
-LC
D
(
Omni-LCD is not available in the U.S.
)
INSTALLATION AND SETUP GUIDE
Keypad Features
Omni-KP
Fixed-Word
Omni-LCD
2-Line Alpha
Backlit Display YES YES
Built-in Sounder Piezo Speaker
The Omni
®
-KP and Omni
®
-LCD are addressable Remote
Keypads designed for use with FBII Omni Series control
panels. Addresses are set via the keypad keys.
The keys on the keypads are continuously backlit for
convenience.
KEYPAD DISPLAYS AND LEDS
The keypads have the following display features:
Model
Fixed
Word
Display
2-line
Alpha
Display
2-digit
Zone
Identifier
Custom
Zone
Descriptors
Omni-KP X X
Omni-LCD X X
The following table shows the LEDs and their functions:
LED Function
Red Lights when the system is armed in any mode
Green Lights when the system is "ready" to be armed.
WIRING AND INSTALLATION
The keypads can be surface-mounted directly to a drywall, or
to a single- or double-gang electrical box.
1.
Remove the case back
by sliding the blade of a
screwdriver-between the tab and the case back on each
side of the keypad as shown in lower diagram at right.
2.
Route wiring from the control panel
through the
opening in the case back.
3.
Mount the case back
to a wall or electrical box.
For wall
mounting of the Omni-KP/LCD in the FR, NL and IT
versions, secure the case back to the wall, being especially
careful to secure the partially knocked-out tamper switch
plunger with its own screw. This assures that separation
of the keypad from its mounting will cause the tamper
switch to activate. Any attempt to pry the keypad open
will also activate the tamper switch in these versions.
4.
Wire directly from the keypad’s terminal block
to
the terminal block on the control board. Wire functions
are marked next to terminals. Labels are as follows: DI
Data In to Control Panel, - Ground, + Aux. Power Plus,
DO Data Out of Control Panel. See table on next page.
5.
Reattach the keypad
to its case back.
ARMED
READY
1
4
7
2
5
8
0
3
6
9
#
STAY
BYPASS
INSTANT
CODE
omni-KP-001-V0
Omni-KP w/ Protective Cover Removed
ARMED
READY
1
4
7
2
5
8
0
3
6
9
#
STAY
BYPASS
INSTANT
CODE
omni-LCD-001-V0
Omni-LCD w/ Protective Cover Removed
ARMED
READY
omni-LCD-002-V0
TO SEPARATE TOP COVER
INSERT SCREWDRIVER
AND PUSH HERE
Separating Case Back From Top Cover

FBII Omni-KP Specifications

General

Brand	FBII
Model	Omni-KP
Category	Keypad
Language	English

Summary

REMOTE KEYPADS Omni®-KP & Omni®-LCD

Keypad Features

Compares features like display and sounder for Omni-KP and Omni-LCD keypads.

KEYPAD DISPLAYS AND LEDS

Details the display features and LED functions for Omni-KP and Omni-LCD keypads.

WIRING AND INSTALLATION

Provides step-by-step instructions for wiring and physically mounting the Omni keypads.

TURNING BACKLIGHT TIMER ON and OFF

Omni-KP Backlight Settings

Instructions for setting the backlight timer on the Omni-KP keypad.

Omni-LCD Backlight Settings

Instructions for setting the backlight timer on the Omni-LCD keypad.

SETTING THE KEYPAD ADDRESS

Keypad Address Viewing

Procedure to view the currently set address for the keypad.

TURNING THE SOUNDER ON/OFF

Omni-KP Sounder Control

Steps to enable or disable the sounder on the Omni-KP keypad.

Omni-LCD Sounder Menu

Guide to using the sounder menu for Omni-LCD, including modes and volume.

SPECIFICATIONS

Physical Specifications

Details the physical dimensions of the Omni-KP and Omni-LCD keypads.

Wiring Specifications

Explains the wiring connections between the keypad and the control panel.

Display Specifications

Describes the display types for Omni-KP and Omni-LCD keypads.

Sounder Specifications

Details the sounder types for Omni-KP and Omni-LCD keypads.

Current Specifications

Lists the current draw for Omni-KP and Omni-LCD in alarm and standby states.