Fellowes Pulsar E 300 - Troubleshooting and Maintenance; Correcting a Bound Document; Waste Clipping Removal and Storage; Common Problems and Solutions

CORRECTING A BOUND DOCUMENT
Additional sheets may be include or removed at any time by opening and then closing the comb as previously described.
REMOVAL OF WASTE CLIPPINGS
The waste tray is located under the machine and is accessed from the right side. For best results empty the tray regularly.
STORAGE
Switch off the machine. Lower the lid. The Pulsar-E comb binder is designed to be stored horizontally on the desk.
TROUBLESHOOTING
Problem Couse Solution
No Green power light
Machine is not switched on
Switch on machine at rear next to plug inlet and at the socket
Red standby light Machine is overloaded when punching Press the punch button. The machine will withdraw the punches and re-set
itself. Continue this process until the punch cycle is complete
Punched holes are not central
Edge gUide not set Adjust edge gUide until hole pattern is correct
Machine will not punch Blockage Check waste tray is empty. Check for blockage to paper entry.
Punch holes are not parallel to edge
Debris is stuck below dies
Take stiff cardboard and slide into the paper entry. Move the cardboard
sideways to release any stray clippings into the waste tray
Waste tray leaks W aste tray is not correctly inserted or 'burst feature' has activated Check waste tray is empty and 'burst feature' is closed
Partial holes
Sheets not correctly aligned to punch pattern Adjust edge gUide and test punch scrap sheets until correct
Damaged hole edges
Possibly overloading the machine Punch plastic covers with paper sheets. Reduce number of sheets being
punched
Waste tray leaks Waste tray is not correctly inserted or 'burst feature' has activated Check waste tray is empty and 'burst feature' is closed
Need Help?
Customer Service ..
www.fellowes.com
Let our experts help you
with a solution.
Always call Fellowes
before contacting
your place of purchase.
WARRANTY
Fellowes warrants all parts of the binder to be free of defects in material and workmanship period set forth above. I n no event shall Fellowes be liable for any consequential damages
for 2 years from the date of purchase by the original consumer. If any part is found to be attributable to this product. This warranty gives you specific legal rights. You may have other
defective during warranty period, your sale and exclusive remedy will be repair or replacement, legal rights that vary from this warranty. The duration, terms and conditions of this warranty are
at Fellowes' option and expense, of the defective part. This warranty does not apply in cases of valid worldWide, except where different limitations, restrictions or conditions may be required by
alme, mishandling or unauthorised repair. Any implied warranty, including that of merchant- local law. For more details or to obtain services under this warranty, please contact Fellowes or
ability or fitness for particular purpose, is hereby limited in duration to the appropriate warranty your dealer.
s
http://www.monomachines.com
http://www.monomachines.com
CORRECTING A BOUND DOCUMENT
Additional sheets may be include or removed at any time by opening and then closing the comb as previously described.
REMOVAL OF WASTE CLIPPINGS
The waste troy is located under the machine and is accessed from the right side. For best results empty the troy regularly.
STORAGE
Switch off the machine. Lower the lid. The Pulsar-E comb binder is designed to be stored horizontally on the desk.
TROUBLESHOOTING
Problem
No Green power light
Red standby light
Punched holes are not centrol
Machine will not punch
Punch holes are not parallel to edge
Waste troy leaks
Partial holes
Damaged hole edges
Waste tray leaks
WARRANTY
Couse
Machine is not switched on
Machine is overloaded when punching
Edge guide not set
Blockage
Debris is stuck below dies
Waste tray is not carrectly inserted or 'burst feature' has activated
Sheets not correctly aligned to punch pattern
Possibly overloading the machine
Waste troy is not correctly inserted or 'burst feature' has activated
Solution
Switch on machine at rear next to plug inlet and at the socket
Press the punch button. The machine will withdrow the punches and re-set
itself. Continue this pracess until the punch cycle is complete
Adjust edge guide until hole pattern is correct
Check waste tray is empty. Check for blockage to paper entry.
Toke stiff cardboard and slide into the paper entry. Move the cardboard
sideways to release any stray clippings into the waste troy
Check waste tray is empty and 'burst feature' is closed
Adjust edge guide and test punch scrap sheets until correct
Punch plastic covers with paper sheets. Reduce number of sheets being
punched
Check waste tray is empty and 'burst feature' is closed
Need Help?
Customer Service ..
www.fellowes.com
Let our experts help you
with a solution.
Always call Fellowes
before contacting
your place of purchase.
Fellowes warrants all parts of the binder to be free of defects in material and workmanship
for 2 years from the dote of purchase by the original consumer. If any part is found to be
defective during warranty period, your sole and exclusive remedy will be repair or replacement,
at Fellowes' option and expense, of the defective part. This warranty does not apply in cases of
abuse, mishandling or unauthorised repair. Any implied warranty, including that of merchant-
ability or fitness for particular purpose, is hereby limited in duration to the opprapriote warranty
period set forth above. In no event sholl Fellowes be liable for any consequential damages
attributable to this praduct. This warranty gives you specific legal rights. You may have other
legal rights that vOIY from this warranty. The duration, terms and conditions of this warranty are
valid worldwide, except where different limitations, restrictions or conditions may be required by
loco I low. For more details or to obtain selVices under this warranty, please contact Fellowes or
your dealer.
s