EasyManua.ls Logo

Fencee power DUO PD10 - User Manual

Default Icon
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
STORED
ENERGY
OUTPUT
ENERGY
OUTPUT
VOLTAGE
OUTPUT
VOLTAGE 500 Ω
SWITCHING
ON/OFF
fencee po w e r DUO PD1 0
1,4 J 1 J 9000 V 5000 V
fencee po w e r DUO PD2 0
3 J 2 J 12 000 V 6000 V
fencee po w e r DUO PD3 0
4,5 J 3 J 11 200 V 6400 V
fencee po w e r DUO PD4 0
5,7 J 4 J 10 000 V 5500 V
fencee po w e r DUO PD5 0
7,5 J 5 J 11 000 V 6600 V
fencee po w e r DUO PD7 0
10 J 7 J 10 500 V 7500 V
35 km 8 km 2 km 1,5 km
60 km 15 km 3 km 1,5 km
100 km 23 km 5 km 2 km
120 km 30 km 8 km 3 km
140 km 40 km 10 km 4 km
180 km 70 km 17 km 8 km
fencee po we r DUO PD 10
fencee po we r DUO PD 20
fencee po we r DUO PD 30
fencee po we r DUO PD 40
fencee po we r DUO PD 50
fencee po we r DUO PD 70
230V ~ / 12 V
Safe Animal Management
|
Power supply - 230 V~ / 12 V
Electric fencing
EN
INSTRUCTIONS FOR USE
+420 730 893 828
www.fencee.eu

Table of Contents

Questions and Answers

  • R
    Regina HoffmanAug 23, 2025
    How to fix Fencee Power Supply when no LED signal is burning?
    • A
      Aaron McdonaldAug 23, 2025
      If no LED signal is burning on your Fencee Power Supply, it could be due to these reasons: * The energizer might be switched off manually. * The battery voltage is decreased below 11,4 V and energizer was switched of f automatically. Reason is protection of battery from its deep discharge (and battery destruction). Replace the battery with a sufficiently charged one or connect adapter – until battery voltage reaches at least 12 V, red LED will be burning.
  • M
    Megan SchneiderAug 29, 2025
    What to do if Fencee power DUO PD10 red LED light is blinking and warning siren sounds?
    • N
      nlopezAug 29, 2025
      If the red LED light is blinking and a warning siren is sounding on your Fencee Power Supply, it means the battery voltage has decreased below 11.6 V. Replace the battery with a sufficiently charged one or connect an adapter.
  • C
    Catherine HollandSep 3, 2025
    What to do if Fencee power DUO PD10 red LED light is blinking?
    • T
      Tammy ByrdSep 3, 2025
      If the red LED light is blinking on your Fencee Power Supply, it indicates that the battery voltage has decreased below 12 V. Replace the battery with a sufficiently charged one or connect an adapter.
  • M
    Michael WellsNov 10, 2025
    What to do if Fencee power DUO PD10 Power Supply voltage is lower than 3 kV and red diode is blinking?
    • L
      Luis CraneNov 10, 2025
      If your Fencee Power Supply system's voltage is lower than 3 kV and the red diode is blinking, here's what you can do: * First, check if the energizer is working by disconnecting it from the fence and switching it on again. A blue or violet LED with a flashing yellow or green LED on the BARGRAPH indicates proper function. If not, the device may be damaged. * If the red LED is blinking, the battery voltage may be low. Replace the battery with a charged one or connect an adapter. * Also, inspect the fence system for lead-ins or short circuits, and use high-voltage cables for supply lines. * Ensure you're using a high-quality conductor with low resistance and a larger diameter, and that the conductor connections are correct. * Check the earthing; add another rod and moisten the soi...
  • C
    carla43Nov 15, 2025
    Why Fencee power DUO PD10 Power Supply does not give pulse?
    • J
      John DurhamNov 15, 2025
      If your Fencee Power Supply system isn't pulsing, several factors could be at play: * The energizer might not be working. Disconnect it from the fence and switch it on. A blue or violet LED with a flashing yellow or green LED on the BARGRAPH indicates proper function. If not, the device may be damaged. * There may be lead-ins or short circuits in the supply lines. High-voltage cable is recommended. * The conductor may have adverse properties. Use high-quality conductor with low resistance and larger diameter. Ensure high-quality correct connection of conductors. * The earthing may be of low-quality. Add another rod, moisten the soil. * There may be lead-in via growth near the fence system. Remove the growth (mow it). * The conductor may be on the ground. Repair fencing, use sp...

Fencee power DUO PD10 Specifications

General IconGeneral
CategoryPower Supply
Output Energy1 J
ModelDUO PD10
Output Voltage10 kV
Input Voltage230 V AC
Protection FeaturesShort-circuit protection