Filtrine B103 - User Manual

To Next Page

Wrench

Cartridge Regulator Valve Assembly

Exploded View

Brass Retaining Ring

Button Trim Ring

Cartridge Regulator

Neoprene

Seal

Spanner

Valve Assembly

Body

See B103 FLUSH BUTTON INSTALL [EB] for valve assembly

part numbers

Hands-Free B103 Bottle Filling Station

Maintenance Instructions

DRAWING

PART NO.

DESCRIPTION

ORDER PART

NO.

1 CARTRIDGE REGULATOR ASSEMBLY 45.0006

BATTERY BOX 6.1712

AA LITHIUM BATTERIES - 4 PACK 51.0592

3 CONTROL MODULE 6.1716

4 SOLENOID VALVE 6.1708

SENSOR (FOR B103 WITH BOTTLE

COUNTER)

6.1714

RED LENSE 6.1717

SENSOR (FOR B103 WITHOUT BOTTLE

COUNTER)

6.1713

7 BOTTLE COUNTER, 3-30VDC 6.1730

ASSEMBLY

SENSOR ASSEMBLY (FOR B103 WITH

BOTTLE COUNTER) - PART NO. 2, 3, 4 & 5)

6.1709

ASSEMBLY

SENSOR ASSEMBLY (FOR B103 WITHOUT

BOTTLE COUNTER) - PART NO. 2, 4 & 6

6.1710

Sensor Activated B103

Maintenance Instructions

To remove the cover plate, unscrew the Jackman

screws from both sides and slide the cover plate out.

Cartridge Regulator Replacement and Flow

Adjustment:

Turn off water to the fixture and depress button on

cartridge regulator to drain water left in the line.

Using the spanner wrench or needle nose pliers,

unscrew the brass regulator retaining ring.

Gently wiggle cartridge back and forth to remove it

from the brass valve assembly body.

Check to ensure that the old neoprene seal was also

removed. Install new neoprene seal on the new

cartridge regulator and install new assembly into the

valve body, ensuring inlet and outlet holes on the

cartridge are lined up and the cartridge is seated

properly in the valve body.

Reinstall the regulator retaining ring and tighten using

the spanner wrench or needle nose pliers.

Turn on water to fixture and test for flow and leaks by

pushing plunger with flat screwdriver.

Adjust the flow by turning the white screw head on the

cartridge regulator. Turn it clockwise to decrease flow

and counterclockwise to increase flow.

Sensor Adjustment:

To adjust the distance of the sensor intensity, turn

yellow phillips head screw on control module circuit

board clockwise to lengthen distance and counter

clockwise to shorten it.

Bottle Counter Reset:

To reset the bottle counter, press and hold the black

reset button (see diagram above for location) for a few

seconds while passing hand across the sensor.

Filtrine Mfg. Co. ∙ 15 Kit St. Keene, NH 03431 USA

800-930-3367 ∙ 603-352-5500 ∙ FAX (603) 352-0330

www.filtrine.com ∙ drinkingwater@filtrine.com

01/15/2020

"HANDS-FREE" BOTTLE FILLING

STATION ASSEMBLY [EB] - PAGE 1

Reset Button

(Water Inlet)

Bottle Counter

" Stop Valve

Body

B103

Cover Plate

Need help?

Do you have a question about the Filtrine B103 and is the answer not in the manual?

Summary

Sensor Activated B103 Maintenance Instructions

Cartridge Regulator Replacement and Flow Adjustment

Procedure for replacing the cartridge regulator and adjusting water flow using the spanner wrench and adjustment screw.

Sensor Adjustment

Adjusting the sensor intensity distance using the control module's adjustment screw.

Bottle Counter Reset

Method to reset the bottle counter by interacting with the reset button and sensor.

Hands-Free Sensor Activation Components

Hands-Free Control Module Instructions

The Filtrine Hands-Free B103 Bottle Filling Station is a sensor-activated device designed for convenient and hygienic bottle refilling. It features a hands-free operation, making it suitable for public and commercial environments where cleanliness and efficiency are paramount.

Function Description:

The B103 Bottle Filling Station dispenses water automatically when a bottle is placed within the sensor's range. The hands-free activation minimizes contact, promoting hygiene. A built-in bottle counter tracks the number of bottles filled, which can be reset as needed. The station is powered by a battery pack, ensuring operation even in locations without direct power access. Water flow is regulated by a cartridge regulator, allowing for adjustment to suit user preferences.

Important Technical Specifications:

Power Source: Battery pack (4 AA lithium batteries).
Battery Life: Approximately 400,000 activation cycles.
Automatic Shutoff: 30-second automatic shutoff to prevent vandalism and water waste.
Bottle Counter: 3-30VDC, tracks bottle fills.
Control Module: Manages sensor activation, solenoid valve operation, and battery power.
Solenoid Valve: Controls water flow.
Sensor Type: Motion sensor.
Certifications: Filtrine is ISO 9001:2015 Certified. The product line is approved and CE Mark available. Complies with NSF/ANSI 372 (Lead-Free).

Usage Features:

Hands-Free Operation: The motion sensor detects the presence of a bottle, automatically initiating water flow without physical contact.
Bottle Counter: A digital display shows the number of bottles filled, providing useful data for usage tracking.
Adjustable Flow: The cartridge regulator allows users or maintenance personnel to adjust the water flow rate to their desired level. Turning the white screw head clockwise decreases flow, while turning it counterclockwise increases flow.
Adjustable Sensor Distance: The sensor's detection range can be customized to prevent accidental activations or to accommodate different bottle sizes. Turning the yellow Phillips head screw on the control module circuit board clockwise lengthens the distance, and counterclockwise shortens it.
Automatic Shutoff: The 30-second automatic shutoff feature conserves water and prevents continuous flow in case of unattended use or vandalism.

Maintenance Features:

Cover Plate Removal: The cover plate can be easily removed by unscrewing the Jackman screws from both sides and sliding the plate out, providing access to internal components for maintenance.
Cartridge Regulator Replacement:
1. Turn off the water supply to the fixture.
2. Depress the button on the cartridge regulator to drain residual water.
3. Unscrew the brass regulator retaining ring using a spanner wrench or needle-nose pliers.
4. Gently wiggle and remove the old cartridge.
5. Ensure the old neoprene seal is removed.
6. Install a new neoprene seal on the new cartridge regulator.
7. Install the new cartridge into the valve body, ensuring inlet and outlet holes align and the cartridge is properly seated.
8. Reinstall and tighten the regulator retaining ring.
9. Turn on the water supply and test for flow and leaks by pushing the plunger with a flat screwdriver.
Flow Adjustment: The water flow can be adjusted by turning the white screw head on the cartridge regulator. Clockwise rotation decreases flow, and counterclockwise rotation increases flow.
Sensor Distance Adjustment: The sensor intensity (detection distance) can be adjusted using the yellow Phillips head screw on the control module circuit board. Clockwise rotation lengthens the distance, and counterclockwise rotation shortens it.
Bottle Counter Reset: To reset the bottle counter, press and hold the black reset button (located on the B103 Body) for a few seconds while passing a hand across the sensor.
Battery Replacement: The device uses 4 AA lithium batteries, which are housed in a battery pack. The battery pack is easily accessible for replacement.
Modular Design: The system is composed of several easily replaceable modules, including the battery box, control module, solenoid valve, and sensor assembly, simplifying troubleshooting and repairs.

The Filtrine Hands-Free B103 Bottle Filling Station is designed for ease of use, durability, and straightforward maintenance, ensuring a reliable and hygienic water dispensing solution.

Filtrine B103 Specifications

General

Brand	Filtrine
Model	B103
Category	Water System
Language	English