FineVu FINE Safer S User Manual

Special features
y
Various modes(stand-by mode / ACC mode) supported
y
Applicable to all types of black box
y
Low power consumption
- Operation : 7~10 mA
- Stand-by : 1~2 mA
y
Indicator LEDs for checking the voltage, timer, and operation
status
y
Short-circuit prevention program applied
Usage/Installation Manual
FINE Safer S
Continuous Power Supply
Main unit
Cigar socket with 5-pin connector
Open the fuse box on the left
side of the driver's seat.
Make sure to install the product only when the engine is turned
off.
The location and appearance of the fuse box may vary depending
on the vehicle you are driving.
Connect the GND
terminal to the
grounding parts.
Connect the 5-pin connector to the main unit.
After finishing with the wiring, wait for 40 seconds for automatic
detection and configuration.
Connect the power cigar jack of the black box into the cigar socket.
Using the double-sided adhesive tape,
securely attach the main power unit to a
desired location.
Close the cover of the fuse box. Now
installation is complete.
Connect the wires of the
continuous power supply
(in the order of B+, ACC and
GND).
8
5-pin connector wiring diagram Installation and use
No Name Remarks
1 White line Black box (+) power
2 Black line Black box (-) power
3 Yellow line B+ power
4 Black line GND
5 Red line ACC (+) power
No Name Remarks
1 B+terminal (yellow) Connects to the B+ of the fuse box.
2 GND terminal (black) Connects to the ground of the fuse box.
3 ACC terminal (red) Connects to the ACC of the fuse box.
4 Main unit
Attaches to a desired location inside the
fuse box of the vehicle using the double-
sided adhesive tape.
5 Cigar socket Connects to the cigar jack of the black box.
6
Double-sided
adhesive tape
Attaches the main power unit to a desired
location inside the fuse box.
7 5-pin connector Connects to the main unit.
The components or appearance of the product may be changed without
prior notice.
1
2
3
4
5
Components and names

FineVu FINE Safer S Specifications

General

Brand	FineVu
Model	FINE Safer S
Category	Power Supply
Language	English

Summary

FINE Safer S Continuous Power Supply Components

Main Unit Components

Identifies the primary device of the continuous power supply system.

Cigar Socket and Connector

Connects the power supply to the vehicle's cigar jack.

Adhesive Tape for Mounting

Used for securing the main power unit inside the fuse box.

5-pin Connector Details

Connects the main unit to the wiring harness.

5-pin Connector Wiring Diagram and Details

White Line (B+ Terminal Wiring)

Connects to the B+ terminal of the vehicle's fuse box.

Black Line (GND Terminal Wiring)

Connects to the ground terminal of the vehicle's fuse box.

Yellow Line (ACC Terminal Wiring)

Connects to the ACC terminal of the vehicle's fuse box.

Second Black Line (GND Connection)

Provides the ground connection for the system.

Red Line (ACC Power Wiring)

Connects to the ACC power source.

Installation and Use Guide

Fuse Box Access Procedure

Open the fuse box located on the left side of the driver's seat.

Power Wire Connection Sequence

Connect B+, ACC, and GND terminals in the specified order.

Grounding Connection Method

Securely connect the GND terminal to suitable grounding parts.

Cigar Socket Connection

Plug the cigar jack of the black box into the vehicle's socket.

Main Unit 5-pin Connector Attachment

Connect the 5-pin connector to the main unit.

Auto-Detection and Configuration Wait

Wait 40 seconds for the product to auto-detect and configure.

Securing the Main Power Unit

Attach the main power unit using the provided double-sided adhesive tape.

Completing the Installation

Close the fuse box cover to finalize the installation.

Product Special Features Overview

Main Unit Features and Controls

Mode Change and Status Check Button

Push-button for switching modes and checking status.

Indicator LEDs

LEDs indicating voltage, timer, and operation status.

Connectors for Main Unit

Includes 5-pin connector and optional 4-pin remote switch connector.

DIP Switch Settings

Cut-off Voltage and Timer Settings

Configure cut-off voltage and timer functions via DIP switch.

Priority of Settings

Explains which setting (voltage or timer) takes precedence.

Mode Change and Operation

Stand-by Mode (Parking Mode)

Power supplied until cut-off voltage or timer limit is reached.

ACC Mode (Driving Mode)

Power supplied only when ACC power is present.

LED Status Indicators

Stand-by Mode LED Status

Describes red LED flashing patterns in stand-by mode.

ACC Mode LED Status

Describes red LED status when ACC power is supplied or off.

Status Information Display

Checking Current Voltage

Briefly press button to check current voltage via LEDs.

Displaying Remaining Timer

Blue and red LEDs display remaining time when timer is set.

Safety and Precautions

Pre-installation Checks

Check component operation before installation.

Intended Use

Use the product solely for supplying power to the black box.

Installation Environment

Install the product with the engine turned off.

Professional Installation Advice

Seek professional help if installation is difficult.

Malfunction Handling

Detach product and stop use if it malfunctions.

DIP Switch Setting Caution

Remove power connector before altering DIP switch settings.

Battery Discharge Risk

Risk of battery discharge due to leakage current on long periods of non-use.

Voltage and Temperature Variations

Acknowledge potential ±2% difference in output voltage.

Manufacturer Liability

Manufacturer not liable for incidental or consequential damages.

Product Specifications

Main Unit Dimensions and Weight

Provides size and weight details for the main unit.

Input and Output Voltage

Specifies the input voltage range and output voltage cut-off.

Current Consumption

Details stand-by and operation current consumption.

Timer Functionality

Lists available output cut-off timer settings.