EasyManua.ls Logo

FireAngel WBS-616 - User Manual

FireAngel WBS-616
34 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WBS-616 User Manual
Wi-Safe Remote
Warning Handset
Part of the Wi-Safe Home Safety
System
N`$JX]\

Table of Contents

Questions and Answers

  • F
    fmorrisJul 31, 2025
    Why does my FireAngel Handsets warning handset “chirp” and the “Signal Failure” light flash?
    • J
      Jonathan ChapmanAug 1, 2025
      If your FireAngel Handsets warning handset “chirps” and the “Signal Failure” light flashes once per minute, it may be due to nearby electrical or electronic equipment interfering with the warning handset. To resolve this, identify the source of interference by moving nearby equipment away from the warning handset or switching it off temporarily. Ensure that the interfering equipment is kept away from the warning handset, or move the handset to a different location.
  • C
    Christopher SuttonAug 6, 2025
    What to do if my FireAngel Handsets warning handset does not respond to an alarm test?
    • R
      Ryan MurrayAug 6, 2025
      If your FireAngel Handsets warning handset isn't responding to alarm tests, verify that the smoke/CO alarm is working and has sufficient battery. Ensure the alarm is Wi-Safe compatible and connected to the warning handset. Also, check the “Signal failure” light. Try moving the warning handset closer to the alarm and re-test. If it then responds, the initial placement was too far or the signal was obstructed.
  • H
    Hannah ShieldsAug 13, 2025
    What to do if my FireAngel Handsets power indicator light is not on when the warning handset is in the cradle?
    • T
      Terry MooreAug 13, 2025
      If the power indicator light isn't on when your FireAngel Handsets warning handset is in the cradle, check that the wall adapter is plugged into a working AC outlet and the outlet is switched on. Also, make sure the warning handset is fully pushed into its cradle.
  • F
    fernandezkeithAug 18, 2025
    Why is my FireAngel Handsets warning handset chirping with no flashing low battery light?
    • M
      Melissa SandersAug 18, 2025
      If your FireAngel Handsets warning handset is chirping, and the “low battery” light is not flashing, the power LED will also be flashing, indicating that the handset is not receiving power. Ensure the handset is fully pushed into its cradle and that the AC power is switched on at the wall socket.
  • S
    Sabrina MooreAug 25, 2025
    What to do if my FireAngel Handsets warning handset doesn't respond while connecting an alarm?
    • A
      Austin HollandAug 26, 2025
      If your FireAngel Handsets warning handset does not respond while connecting an alarm, make sure the alarm is Wi-Safe compatible and working correctly. The alarm may already be recognised by the warning handset. Return the Handset to the cradle and carry out a self test on the alarm.

Summary

INTRODUCTION

OVERVIEW OF THE FIREANGEL WI-SAFE HOME SAFETY SYSTEM

DEFINITIONS

RF

Defines Radio Frequency as the method of communication for the system.

LED

Defines Light Emitting Diode as the visual indicators on the handset.

AC Adaptor

Defines the alternating current adaptor used for power.

Encryption Protocol

Describes the secure communication method used by FireAngel.

APPLICATION

POSITIONING

WHAT ARE THE LIMITATIONS?

HOW TO INSTALL YOUR WI-SAFE WARNING HANDSET

I Preparation

Ensures users understand the manual and compatibility before installation.

2 Installation

Guides users through physically setting up the warning handset and its cradle.

Connecting to Wi-Safe Alarms

Details the process of pairing the handset with Wi-Safe smoke and CO alarms.

Testing

Explains how to verify the system's functionality after setup.

OPERATION

5 Basic Function

Explains the normal, alarm, torch, and reset states of the handset.

6 Removal of AC (Mains) Power

Details how the handset behaves and alerts when AC power is lost.

7 Removal of the Warning Handset

Explains the procedure and warnings when removing the handset from its cradle without an alarm.

8 Battery Replacement

Guides users on how to replace the handset's internal battery.

9 Signal Failure

Describes issues related to lost RF signals between alarms and the handset.

10 System Integrity Check

Outlines checks needed after changes to the system or home environment.

II Audible and Visual Indicators

Explains the meaning of different LEDs and buzzer sounds on the handset.

WHAT TO DO IF YOUR WARNING HANDSET ALARMS

I What to do in the Event of a Smoke Alarm Sounding

Step-by-step guide for responding to a smoke alarm event.

2 What to do In the Event of a Carbon Monoxide Alarm Sounding

Step-by-step guide for responding to a carbon monoxide alarm event.

REPAIR

TROUBLESHOOTING

DISPOSAL

5 YEAR LIMITED WARRANTY INFORMATION

RETURNS

PRODUCTS IN THE WI-SAFE RANGE

FireAngel WBS-616 Specifications

General IconGeneral
BrandFireAngel
ModelWBS-616
CategoryHandsets
LanguageEnglish